Filter Results By:
Products
Applications
Manufacturers
Test Bench
worktable including instrumentation, fixturing and unit under test.
See Also: Test Benches
- Taylor Dynamometer, Inc.
product
400 HP Complete Bench Hydraulic Test Center
HTC-400
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 400 hp (298 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators).The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
Radar Test System
UTP 5065
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
product
Pressure Loss Test Bench For Measuring Unit Of Gas Meter
Bofa Instrument & Equipment Co., Ltd
Pressure loss test bench for gas meter measuring unit of gas meter is ideal device to check pressure loss of measuring unit of gas meter, the test bench is designed as per gas meter production crafts and testing requirements, adopting imported pneumatic components and accurate sensors. It is an ideal testing device to be used in production line for gas meter manufacturer
-
product
Spectrum Analyzers
A refurbished spectrum analyzer is the best solution if you are looking to stretch your budget. The spectrum analyser is typically a more expensive piece of test equipment when compared to other general purpose test instrumentation. Depending on your test needs and budget a new spectrum analyzer may be the preferred choice. We have a very wide selection for you to choose from and a product for every budget.A spectrum analyzer is found in three basic forms, bench top, handheld, and portable. The spectrum analyser enjoys a long useful life and good resale value because of its fundamental use, the measurement of the spectrum of a signal. Microprocessor speeds change but frequencies do not. Basic and real time signal and spectrum analysis is always a test need especially now given the wireless world we live in. As wireless consumer and industrial devices continue to come on the the market, the spectrum analyzer can be found in more and more design, in house test, manufacturing, quality, field test, and remote repair applications.Test Equipment Connection offers Spectrum Analyzers in a various range of prices and categories, allowing you to find the equipment you need. Search by Frequency, number of channels, brand or price range. Test Equipment Connection has made it easy to find the equipment that is right for you.
-
product
Power Analyzers
Real drive and test bench applicationMultiple power analyzer in one instrumentUltra flexible channel configurationWide range of fundamental frequencyCAN interface for automotive and test bench linkInternal current transducer supply and TEDS support
-
product
Modular Multilevel Converter (MMC) Test Bench
Research into innovative HVDC interconnections and FACTS applications requires a flexible hardware architecture that allows testing of new topologies and switch configurations.
-
product
Test Sockets
BGA/LGA
There are a lot of options when it comes to bench test sockets. Save yourself and your lab time, money and frustration by working with Ardent for truly customized test socket solutions to meet your needs and do the job with high performance, reliability and quick turnaround that you need and deserve.
-
product
Universal test bench for optronic maintenance
COPI
COPI is a universal test bench used for test and maintenance of all kinds of optronic equipments.
-
product
AC Power Supply and Frequency Converter
P Series
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
product
Three Phase Meter Test Bench
Supreme Instrument Laboratories
Three phase meter test bench suitable for calibration & testing of AC Ammeters, Voltmeters, Single phase Energy Meters, Watt Meters, Power Factor Meters, Three Phase Two Wire & Three Phase Four Wire Energy Meters Trivector Meters, Maximum demand indicators, of active & reactive systems, Three phase 3 wire & 4 wire watt meters, Var Meters, Power Factor Meters etc.
-
product
50W Power Supply, 35V, 1.4A or 60V, 0.8A
E3643A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 48W, single output E3643A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
product
Adjustable Clamshell Bed of Nails Testers
AdjustaBON Family
Designed for quick test development. This fixture can be configured to probe almost any circuit board in just a few hours. Once the perfect test is developed, move this light weight fixture out to the production floor to evaluate your production line test strategy prior to buying permanently drilled test fixtures, or while waiting for your drilled fixtures to be delivered. The AdjustaBON competes with the Flying Prober. There are many advantages over the flying prober. Setup is simple and intuitive and can be much quicker than programming a flying prober. Small size provides versatile bench top operation right where you need it. Maintenance costs are insignificant in comparison. The total cost of this fixture is in many cases less than the yearly maintenance cost of a flying prober. It would be possible to buy one of these fixtures every year for the price paid just to maintain one flying prober and it is about 1/20th the purchase price
-
product
Water Meter Test Bench
LS-4B
Hong Kong Songyang Industrial Ltd.
The water meter test bench is made up the platform, clamps, back and front pipe, flow counter group, standard measuring instrument and the outlet valve.When the inlet is connected with the stable water source, the water will get to the standard measuring instrument through the straight pipe. Compare the value of the checked water meter with that of the standard measuring instrument, the valve error that the water meter reads will be acquired.
-
product
Waveform Generators
Drive your test systems forward with PXI instruments from Astronics. Small size, power-packed, and cost-effective, these waveform generators provide the perfect upgrade for your test bench.
-
product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
Injector Expert
InEx-2
Injector Expert InEx-2 is a versatile tool for advanced diagnosis of Common Rail injectors. It enables electrical and mechanical testing of injector actuators – solenoids and piezoelectric stacks. Its feature to generate injector control signal may be used for testing injector performance on a test bench. Technical capabilities of InEx-2 allow the following tests:
-
product
Bench Power Supply, DC, Single, Adjustable, 1 Output, 1 V, 36 V, 0 A, 3 A
72-8345A
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
product
Analog/Linear Tester
Amoeba 4200
4200 is capable of running multiple test sites independently with a parallel efficiency of up to 85% for quad-site and octal-site testing.It comes with test development and production software suite, which makes the transition from test development and bench characterization to production seamlessly.
-
product
Power Electronics Test Bench
OP1300
The multi-purpose and ready-to-use Power Electronics Test Bench combines a state-of-the-art Hardware-in-the-Loop (HIL) simulator from OPAL-RT with Imperix’s Rapid Control Prototyping (RCP) system and real power hardware. It enables rapid development of power electronics, drives and smart-grid applications across industry and academia.
-
product
Test bench for Infrared Focal Plane Array detectors
BIRD
The BIRD bench enables characterization of any types of Infrared Focal Plane Array (IRFPA) detectors.
-
product
Gas Meter Test Bench
Bofa Instrument & Equipment Co., Ltd
Ideal instruments to measure and calibrate domestic gas meters.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
Mass Burette Flow Detector
FX-1100 Series
The FX-1100 Series Mass Burette Flow Detector takes the position of the fluid surface inside the burette as the head pressure using the differential pressure detector attached at the bottom and directly measures the flow of fluid as a mass based on changes in this pressure. It does not require calculation correction of temperature and specific gravity, and has many advantages such as high accuracy and extremely less affected by air bubbles, which enable to measure fuel consumption in the tests such as chassis dynamometer and engine bench. The 3 models are available according to the measurement range and application.
-
product
SF6 Specialist Gas Analyzers Range
The Rapidox SF6 6100 Bench gas analyser is designed for controlling and monitoring the quality of SF6 gas over a range of applications, including medium & high voltage gas insulated electrical equipment, SF6 gas purity tests, medical testing, manufacturing and laboratory-based research and development.
-
product
Single Phase Energy Meter Test Bench Type KP-S1000-A
Bofa Instrument & Equipment Co., Ltd
Single phase test bench, type KP-S1000-A, is a new generation, high precision energy meter calibration equipment. It can test mechanical energy meter and electronic energy meter, in spite of open or closed test link (I-P link). It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
product
Airproof Test Bench For Complete Gas Meter
Bofa Instrument & Equipment Co., Ltd
Airproof test bench for complete gas meter is a device to test a complete gas meter airproof. The bench is adopting compare method by comparing tested meters with a standard tank. It is suitable for gas meter with steel case or aluminum case.
-
product
Analog
Create complete systems while streamlining your development process and reducing your design risk. We design our mixed-signal, linear, interface and power products for seamless integration with our extensive portfolio of microcontrollers, digital signal controllers, microprocessors and FPGAs. Well-known for our thorough documentation, we provide parts that work on the bench the same way they’re described on paper. We also provide evaluation boards to demonstrate functionality, an intuitive Integrated Development Environment (IDE), simulation software and other design resources to create a rapid design, prototype and test environment for all aspects of your system design.
-
product
Environmental Simulation Chambers
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
