Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
VTAC Wired
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The results show no significant deviation from the SFP signal until approximately 6.25 GHz. Even at 6.25 GHz, there is only -1dB of difference between the two patchcords, which is approximately a 10% loss. With signal integrity playing such an important role in high speed testing, the obvious choices for high bandwidth data testing are VTAC Wired products.
-
product
Bit Error Rate Tester
Eye-BERT Gen2
The Eye-BERT Gen2 builds on our original Eye-BERT, adding extended data rates, mixed mode testing capability, and a color touch screen. The extended data rate allows for testing of links in the 125Mb to 11.4Gb range all in a single unit. The Eye-BERT Gen2 offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of SFP and SFP+ transceivers as well as link verification and performance testing all in a single unit.
-
product
Thermoelectric Cooler Controller
Analog Devices Thermoelectric Cooler Controllers work with cooler based photonics, offer the smallest size, the best efficiency and the most robust solutions. It has a linear power stage with the linear driver output and a pulse width modulation power stage with the SW output. Depending on the part number, it offers digital PID control or analog PID control or both. Our TEC controllers support a variety of MSA based optical modules such as SFP, SFP+,QSFP+, CFP/CFP-2/CFP-4 and QSFP28.
-
product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
product
Bi-directional SFP Modules
BiDi SPF
The DIAMOND SA flexos BiDi-SFP modules (transceivers) make it possible to transfer data via fibre optics. The Bi-Di SFP modules are available in single-mode and Gigabit Ethernet. The SFPs have metal housings with latches for the simple removal of the module. They are compatible with connector types F-3000™ and LC.
-
product
40Gbps Ethernet Packet Generators
Axtrinet (AXTRINET IS A TRADING NAME )
40Gbps QSFP+ & 10Gbps SFP+ ports, Support optical & copper transceivers, Wire-rate performance on all ports, Compact & Portable, Intuitive Graphical Control Interface, Control multiple units from single GUI, Test Automation with TCL interface
-
product
ARINC 664 Part 7 16 port Lab Switch
SWT-664-16
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Sixteen (16) port non-blocking switch - Crossbar design, with 32 Gbps total transmit and receive bandwidth - Each port can operational at 10/100/1000 Mbps line rates - SFP interface supports RJ45 copper and optical connections - Traffic policing and filtering - 4096 Virtual Links configurable - BAG ranges of 0.5ms to 1600ms - Out of band access through Ethernet or serial port - Switch and port statistics available via snmp - Supports on-board storage of multiple configuration files
-
product
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437
Convert between 1000BASE-T1 (automotive Gigabit Ethernet) and SGMII Interface. The 1000BASE-T1 SFP Module is the cutting-edge solution to convert between 1000BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 1000 Mbit/s full-duplex.
-
product
SFP+ Cable, 0.5m
784076-0R5
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model … has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
QSFP+ Twinaxial Cable, 5m
785685-05
1-Pin, Male QSFP+ to 1-Pin, Male QSFP+ SFP Cable - The QSFP+ Cable connects to the quad small form-factor pluggable (QSFP) ports on some PXI Ethernet Interface Modules and other hardware devices. The model also has multimode optical fiber options that you can use in tandem with QSFP+ optical transceivers. The cable is rated for transmission speeds up to 40 Gbps and is offered in different lengths.
-
product
Pump Laser Diode Driver
S-110
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
1U Rackmount Network Appliance Platform With Intel® Xeon® Processor D-1527/ Pentium® Processor D1508 And 10 LANs
NA720
The NA720 is built on the server-class Intel® Xeon® D-1527 processor (codename: Broadwell-DE) and Pentium® processor D1508. The NA720 comes with two 10GbE SFP+ ports, eight Gigabit Ethernet ports and two expandable LAN modules supporting 1GbE/10GbE/Fiber/Copper/Bypass with a maximum of 26 LAN ports. Four DDR4-2400 MHz R-DIMM/U-DIMM sockets can provide system memory of up to 128GB and support both ECC and non-ECC memory types. For storage, it supports one mSATA and two 2.5” SATA hard disk drives. This high performance Intel® Broadwell-DE network appliance is an ideal solution for enterprise firewall, network bandwidth controller and UTM applications.
-
product
Fiber Cable, Multimode, OM3, 50m
784184-50
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
24 Port CPCI Managed Layer Two Switch
CP217
The CP217 is a 6U single slot Compact PCI (cPCI) module that has 24 ports of GbE. Eight ports via RJ-45 and four ports via SFP as a single slot. The Module come with an optional daughter board which has an additional 12 ports of GbE via SFP which can provide Fiber or Copper interface.The switch is managed via http and supports a rich set offeatures such as VLAN, Spanning tree, QoS, Mirroring, etc.
-
product
Xtium2 Frame Grabber Family
The Xtium2 series leverages the PCIe Gen3 x8 platform to deliver high- speed image transfers to host memory without CPU overhead. Featuring Camera Link HS® interface standards, supports Active Optic Cable and SFP+ modules, CoaXpress® 12, and Camera Link®.
-
product
NI-7932, Xilinx Kintex-7 K325T FPGA, 2 SFP+ Port, Controller for FlexRIO
783765-01
The NI‑7932 features a programmable FPGA and embedded processor optimized for deployment in the field for reliable, extended operation for applications requiring advanced I/O capability with embedded signal processing. It includes a Xilinx Kintex‑7 K325T FPGA, 2 GB of onboard DDR3 DRAM, a dual‐core ARM Cortex‑A9 processor running NI Linux Real‑Time, and 2 SFP+ ports for data streaming. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
4-port LAN Module With Intel® I350-AM4/I211-AT Ethernet Controller
AX93336
The AX93336 LAN module is built with an Intel® I350-AM4/I211-AT GbE Ethernet controller, incorporating Jumbo Frames and Intel® VT-c (Intel® I350-AM4) to optimize network traffic processing. It also comes with an optional LAN bypass function to ensure smooth network connectivity at all times, making it an ideal solution for users seeking better protection of their essential business communications in the event of a power outage, system shutdown or crash. This LAN module’s high-density design is specifically adapted for Axiomtek’s 1U and 2U rackmount network appliances, featuring four 1 GbE RJ-45 or four SFP ports plus a PCIe 2.0 x8 golden finger for expansion flexibility, giving customers the freedom to streamline their individual network infrastructure deployments to fulfill fast-changing networking demands quickly and cost-effectively.
-
product
FOTS-ORL
S-120
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
Test Solution
Eye-BERT MicroX
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-time eye opening monitor and eye scanning capability can aid in troubleshooting by providing the operator with additional link quality information. Other features include Autonomous pattern detection, SFP diagnostic tools, and wavelength tuning (per transceiver capability). With a click of a button the Eye-BERT MicroX will automatically test an SFP module based on its advertised capabilities and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
product
SFP BIDI
2.5 Gbps LC BIDI
Is specifically designed forhigh performance integrated duplex data link overbi-directional single mode optical fiber. Thehigh-speed laser diode and photo diode areprovided as a light source and a detector,respectively.
-
product
Optical Fiber Transceivers
Optical Fiber Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP). Fiberinthebox provide a full range of optical transceivers, such as SFP+ (SFP Plus) transceiver, X2 transceiver, XENPAK transceiver, XFP transceiver, SFP (Mini GBIC) transceiver, GBIC transceiver, CWDM/DWDM transceiver, 40G QSFP+ & CFP, 3G-SDI video SFP, WDM Bi-Directional transceiver and PON transceiver.
-
product
ATCA I/O Rear Transition Module (RTM)
ART001
The ART001 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe and Management I/O for the front blade. The module is designed to mate with any ATCA Carrier. ART001 provides PCIe x8 access via an iPASS connector to the rear. The GbE rear access is provided via six SFP ports and five RJ-45 ports. The module has dual 10 GbE PHY which mates to the host via the zone 3 connector and provides dual SFP+ to the rear.
-
product
PXIe-8238, 10 Gigabit PXI Ethernet Interface Module
784976-01
10 Gigabit PXI Ethernet Interface Module—The PXIe-8238 is a high-performance 10-Gigabit ethernet SFP+ interface for PXI Express based on the Intel 82599 10Gb ethernet controller. It includes two 10-Gigabit ethernet SFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
product
Ethernet To Fiber Optic Converters (Point To Point)
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
product
SFP+ Cable, 1m
784076-01
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model … has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Fiber Cable, Multimode, OM3, 100m
784184-100
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
1000BASE SFP Transceivers
CommFront offers a range of high-quality, high-performance SFP transceivers ranging from MM 850nm / 0.3 miles (550m) to SM 1550nm / 100 miles (160km). SFP (Small Form-Factor Pluggable) is a compact, hot-pluggable network interface module used for data communication and tele-communication applications. SFP equips with one or two fiber optic connectors (e.g. LC connectors) for connecting a fiber optic cable or sometimes an RJ45 connector for connecting a copper cable. Because of its compact size and flexibility, many Ethernet Switches come with SFP ports so individual ports can be equipped with any suitable type of transceiver as required.
