Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Dual 12:1 High Voltage Power MUX
40-331-002
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
High Voltage Isolation Switch Contact Pressure Tester
WA1401
Wuhan Sangao Electrical Test Installations Limit Co.
Isolation switch is the high voltage switch equipment, it was large and frequently use in power system . The outdoor isolating switch is the only completely exposed in the atmospheric environment electrical equipment, It is also a electrical equipment affected by climatic conditions influence the most direct and most serious. The operating conditions is relatively poor, It is easy to generate fault of mechanical or electrical. Especially the finger contact part is easy to be affected by rain, dust and harmful gas invasion, resulting in poor contact caused fever, provide the spring with contact pressure due to heating and annealing for reducing the pressure, so that more cause finger heat form vicious spiral eventually burn out finger accident. In maintenance often only pay attention to replace the obvious failure and fracture of spring, but spring to reduce the pressure can not judge and replacement, so again in the operation, each finger current distribution by the pressure difference, The greater the difference between the current distribution is not uniform, long-term operation will occur is bad and the overheating. Fever finger will be vicious spiral, a finger contact bad will spread over the entire bad contact. At the same time, there are a lot of isolating switch contact pressure can be adjusted, if in maintenance adjustment pressure is not enough or each finger to adjust the pressure difference will also appear afore-mentioned phenomena.
-
product
Slip Ring Test System
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
product
High Accuracy Digital Puncture Tester
KT-5000Pi
This product improves the absurdity that the existing Puncture Tester has many errors between the indicated voltage on its meter and the real output voltage, and also that one cannot check how much current flows during test, and then attaches a voltage meter and a current meter. Its accuracy is high due to Digital method adopting a three point adjustment type. Also, for user's convenience and for making easy to connect with automation line, many input, output functions are added. Now, Puncture Tester also should be accurate and a high-grade product
-
product
DC High Voltage Break Down Tester
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
product
Digital 5KV High Voltage Insulation Tester
Model KM 6305IN
Kusam Electrical Industries Limited
• Microprocessor-controlled.• Tests insulation resistance up to 10 TΩ • 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V.• AC / DC Voltmeter.• Short-circuit current up to 5mA• PI (Polarization Index) indication.• DAR (Dielectric Absorption Ratio) indication.• Auto-ranging on all insulation ranges.
-
product
Fully Automatic Transformer Oil Test Set
1. Test as per International standards NMC insulating oil testers are fully automatic micro controller based system,completely self-contained,compact and portable giving smooth variable test voltage from 0 to 60, 80, or 100 kV for testing the dielectric strength of insulating oil in accordance with all international standards like IEC156/IS6792/ASTM D 1816/ASTM D877/ UNE 21 specifications.2. Auto mode NMC insulating oil testers are fully automatic type.1) IEC-156, IS6792, ASTM D 877, ASTM D 1816, UNE 21.2) Withstand Test A3) Withstand Test B4) 5 Minute Test5) User defined3. 100 Test results storage capacity NMC insulating oil testers has a storage capacity of 100 test results which can be recalled and printed.4. LCD display NMC insulating oil testers use LCD for easy readability of the BDV test results.5. Built in printer The printer used is a thermal paper print outs.The paper rolls can be easily installed by any person.6. User Friendly RS 232 Interface RS 232 interface is very easy to use to communicate stored data which can be saved in text format.7. Safety protection Safety interlocks are provided on the test chamber.Zero interlock protection to ensure operator safety.8. Accurate Performance The kit not only has all basic functions of an insulating oil tester but also has unique features that are seldom seen in similar products. For e.g. PROOF test A, PROOF test B, 5 Minntes test, LCD to display all test data.It ensures high work efficiency and reliability in any tough environment.
-
product
External Measurement Instrument Port | Add-On Option to CableEye HVX Series Testers
Item 835
Measure 10 GΩ Isolation at 100 V
This new capability is of special interest to customers requiring measurements of extremely high isolation resistance at very low voltages. The HVX-series option may be ordered with new testers or added as an upgrade to previously purchased systems.
-
product
Battery Cell Insulation Tester
Chroma 11210
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
product
IST(5KV~15KV)High Voltage Micro Ohm Meter,Insulation Resistance Tester Kit
Chongqing Assen Power Equipment Co., Ltd
ISF High Voltage Ohm Meter has a large LCD screen gray backlit display, data storage, data access, alarm, and automatic shutdown functions.
-
product
AC Hipot Tester /DC Hipot Tester
YD-Series
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
YD series HIPOT tester is applied to test the insulation ability of electric power equipments and insulation materials at power frequency high voltage. The insulation test result of the tester is go or not go. Also the YD series HIPOT tester is a universal power source in HV test. The maximum output voltage and capacity could be customized according the requirements of custom.The tester is consists of single HV transformer and main control box. There are two kinds of HV transformer according to the insulation materials of the HV transformer.They are dry HV transformer and oil HV transformer. For the dry HV transformer the insulation material is epoxy resin.For oil HV transformer the insulation material is insulation oil. The dry HV transformer has a smaller size and less weight than oil HV transformer. But the maximum output voltage is less than 100kv for dry HV transformer. The functions of the main control box are voltage output regulation, protection in emergency and voltage/current value indication
-
product
300kV/5mA DC Hipot Tester
HDZG
HD Power Test Equipment Co.ltd
HDZG-305 300kV/5mA DC high voltage tester is used for testing DC high voltage for zinc oxide arresters,magnetic blowing arresters, power cables,generators,transformers,circuit breakers and other equipments,which is suitable for electric power branch,power department of factories,scientific research units,railway,chemical industry,and power plants.
-
product
Advanced Continuity and Hipot Tester
Easy Touch Pro
The Easy-Touch Pro is a self-contained high voltage cable tester designed for easy integration within your manufacturing process. With an integrated Windows® OS and Cirris software, this tester provides a reliable combination of function and flexibility.
-
product
Hipot Testers
95X Series
Vitrek built the 95X Series from the ground up with DSP technology – to bring you the safest, fastest, most capable, feature rich hipot testers available. The 95X Series combines high output power, with a wide range of AC & DC voltage outputs and extremely low leakage current measurement. Then we added a 4-wire milli-ohmmeter with dynamic range up to 100K ohms and an overlapping Tera-ohm class Insulation Resistance function. Top that off with an available 40 Amp Ground Bond capability and you’re just beginning to get a feel for what the Vitrek 95X Series Hipot Testers can do for you.
-
product
Raptor HV High Voltage Tester
The Raptor-HV, also called the high voltage slave, is an optional product that extends the Raptor’s applications to tests that require the use of a moderately high AC voltage.
-
product
6-12V Duality High And Low Voltage Trouble Shooter
1669
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems, test for circuit and spark plug.1. Check spark plug on secondary or high voltage. 2. Use as a continuity tester to check on low voltage circuits.
-
product
High Voltage Testers
GLP1
GLP1-testers are quite compact testers for testing the electric safety and functioning of electric products according to various national and international regulations. Whether manually operated, automatically run, or integrated in a production line - the testers perform excellent work.AC tests 0-30 kVDC Tests 0-6 kVA large variety of GLP1 testers are available to suit your application and technical requirements
-
product
Insulation Resistance Tester For PV (Judge Deterioration Point)
MIS-PVS
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PVS is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
product
Automatic High Voltage Wire Harness Testers
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
product
5kv 10kv hi-pot tester
RK2671
Shenzhen Chuangxin Instruments Co., Ltd.
5kv,10 kv hi-pot tester withstand voltage tester KR2671 Voltage tester high quality
-
product
DIGITAL TURNS TESTER AND DIGITAL LCRTZ METER
TURNS-LCRTZ
Digital TURNS TESTER with LCR for Counting / Measuring Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity , DC Resistance , Inductance (L), Capacitance (C), DC Resistance, Rac, Q, D, ESR and Tan.Toroidal Turns Platforms :TTPT100 : 5 T - 1000 T , TTPT1000 : 500T-10000 T The Platform has 2 connections for the coil and 2 for the probe wire. Measurement principle is based on dynamic comparison of the voltage across one turn and the coil. You will be able to get the polarity or winding indication with respect to the one turn reference.Accuracy : + 0.2% + 0.5T for high and medium permeability cores at suitable test frequency. Internal Diameter must be able to pass a wire as thin as 0.2 mm. External Diameter as high as 200 mm.Test Frequency Selectable in Step : 50 Hz, 100 Hz , 500 Hz, 1 KHz, 5 KHz, 10 KHz. Test Voltage adjustable : 100mV to 1V in steps of 50mV.
-
product
HIPOTS (High Voltage Testers) / AC Hipots
5 kV Analog
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Variable from 0-5 kV. Multi-range kV & mA meters. Zero start interlock protection.
-
product
High Voltage Tester
The AC /DC High Voltage Test Set that we offer to our clients is widely used at electrical maintenance departments and workshops. It is chiefly used to perform routine maintenance of numerous electrical devices and equipment. Apart from that, this product is used to check the quality of insulation provided in any electrical device.
-
product
Gas-Filled Hv Testing Transformer
GTU-300KVA/600KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test, and for testing all GIS switchgears and GIS components such as insulators, insulating tension pole, GIS voltage transformer and so on, the PD test can be performed under the general environment because of the merits of encapsulation, the PD level of our equipment can be lee than 3pC, and it can be added a HV bushing to perform the withstand voltage test at the same time. Small and compact dimensions resulting in minimum space requirements. Light-wight components. Rugged construction to withstand long transportation stresses. Direct flanging to the test object. High safety for tester because of encapsulation of all HV parts. Large range of application in conjunction with HV bushing for withstand voltage test. Built-in HV measuring capacitor and coupling capacitor. Built-in HV disconnecting switch to separate multipath test object connector to ensure the safety of HV testing.
-
product
H.V. Proving Unit (DCV)
2713 PU
Standard Electric Works Co., Ltd
● Designed to proof: -Phasing sticks. -High voltage detectors (contact type only, not to be used with non contact proximity detectors.) -High voltage and voltage testers.● Battery operated.● Led indicates when power is “ON”.● Small and hand-held.● Quick connection with normal 4mm test leads.
-
product
Programmable High Voltage Tester
The high Voltage also known as di-electric withstand tester comes with customized facilities like voltage rampup rate zero interlock, Plus the user may specify the voltage level and leakage milliampere level so as to suit its testing needs.
-
product
Impulse Withstand Voltage Tester
SUG255
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
product
HIPOT Insulation Testers
Crown high voltage, transformer type hipot insulation testers are safe, easy to use for quick, positive determination of grounds, shorts, and broken wires in motors, transformers and other low voltage equipment or wiring systems. A turn of the selector switch gives a selection of seven voltages; 500, 1080, 1250, 1500, 1750, 2000 or 2500 volts calibrated to +/- 5% accuracy; NEMA recommendation for insulation test is twice normal voltage plus 1000 volts. Since this instrument has a capacity of 2500 volts, it readily accommodates all normal requirements.
-
product
Partial Discharge Tester
19501-K/19500
Chroma 19501-K partial discharge tester combines hipot test and PD (partial discharge) detector functions in one instrument. The device is capable of a maximum 10kV AC output with leakage current measurement range of 0.01uA and a minimum partial discharge detection of 1pC. The tester is specifically developed to test high voltage semiconductor components and high insulation materials.
-
product
Surge / DC Hi-Pot Consoles
HC Model
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
product
Digital 5kV High Voltage Insulation Tester
4305 IN
Standard Electric Works Co., Ltd
• Protection class: IP65 (Lid closed)• 2 Lines × 16 Characters LCD• Microprocessor-controlled• Tests insulation resistance up to 1 TΩ • 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V• AC / DC Voltmeter (30~600V)• Short-circuit current up to 5mA• PI (Polarization Index) indication• DAR (Dielectric Absorption Ratio) indication• Auto-ranging on all insulation ranges• Auto-hold function to freeze reading• Overload protection• Adjustable testing duration: 1~30 minutes• Internal memory for data storage• Displays testing duration for insulation measurement • Auto-off function• 200 measurement results can be saved in memory and recalled on display
