Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Mini Coax, Contact, Receiver, RG178
610104141
Primary mating contact 610103130. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance ≤ 5 mΩCable Specifications RG178Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
Resistors for Calibration of Current Measuring Systems and Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
Is designed and made according to the Standard JB/T8225-1999 for DC resistors used in laboratory and electrical engineering.By using full closed structure and automatictemperature control it ensures resistor good long-term stability and small temperaturecoefficient. This DC resistor is very suitablefor DC current measurement and calibration of current measuring systems and current sensors. The maximal measuring current is 100A with measuring accuracy of ±0.02%
-
product
Railway Rolling Stock
The railway industry is known for very extreme working conditions for electrical equipment, where vibration, dust, temperature, humidity variations and electric interference requires that all electrical components must work under very harsh conditions. With a heavy demand on reliability Mors Smitt railway components are manufactured and tested to offer long effective hours of work and low life-cycle costs.
-
product
Measurement and Analytics Solutions
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
product
Miliohm Meters
Measures low resistance to detect faulty connections that degrade electrical system performance.Prevent electronic failures.
-
product
Solenoid Valve Tester
DZ800
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
product
Analyzer System
Ruggedized Test Systems (RTS)
This analyzer is a rugged, field deployable system that detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex.
-
product
Signal Interface
Our signal interface products provide signal conversion and electrical isolation between sensors and other field devices and a control circuit. Intrinsic safety modules add Zener diodes, which limit the amount of electrical energy on intrinsically safe circuits.
-
product
Rectal Probe For Mice (Isolated)
RET-3 ISO
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 2m
A037DF4-T-0A200
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
DisplayPort v1.3 Protocol Analysis Probe
FS4500
The FuturePlus FS4500 DisplayPort Analysis Probe provides a mechanical, electrical and software interface to the DisplayPort bus, a digital display interface standard supported by the Video Electronics Standards Association (VESA). The FS4500 is used to design and debug computer motherboards, monitors, home theater systems, and silicon chips incorporating DisplayPort technology.
-
product
8-Channel VME Time-to-Digital Converter
V680
The V680 is an 8-channel time-to-digital converter used to record the time of occurrence of eight independent electrical pulse inputs, each measured relative to a single, common reference input. Each input channel can time its event "hit" with 48.82-picosecond resolution and 48-bit dynamic range.
-
product
Safety
Chroma Systems Solutions, Inc.
The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.
-
product
IEC60884 Fig22 Plug Socket Covers Pendulum Impact Test Apparatus
CX-BC22
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig22 plug socket covers pendulum impact test apparatusMeet the standard: IEC884-1 Figure 22-26,, IEC60068-2-75Uses: Suitable for household and similar plugs and sockets, wall mounted mounting boxes, screw glands, covers, switches and other electrical accessories for mechanical strength test
-
product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-02
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
Handheld instrument for electrical conductivity measurement of non-ferromagnetic metals. The electrical conductivity can be used for determining material properties, like hardness, strength, heat damage and material fatigue of metals. Rapid and simple on-the-spot conductivity measurement of non-ferromagnetic metals acc. to DIN EN 2004-1 and ASTM E 1004.
-
product
High Voltage Isolation Switch Contact Pressure Tester
WA1401
Wuhan Sangao Electrical Test Installations Limit Co.
Isolation switch is the high voltage switch equipment, it was large and frequently use in power system . The outdoor isolating switch is the only completely exposed in the atmospheric environment electrical equipment, It is also a electrical equipment affected by climatic conditions influence the most direct and most serious. The operating conditions is relatively poor, It is easy to generate fault of mechanical or electrical. Especially the finger contact part is easy to be affected by rain, dust and harmful gas invasion, resulting in poor contact caused fever, provide the spring with contact pressure due to heating and annealing for reducing the pressure, so that more cause finger heat form vicious spiral eventually burn out finger accident. In maintenance often only pay attention to replace the obvious failure and fracture of spring, but spring to reduce the pressure can not judge and replacement, so again in the operation, each finger current distribution by the pressure difference, The greater the difference between the current distribution is not uniform, long-term operation will occur is bad and the overheating. Fever finger will be vicious spiral, a finger contact bad will spread over the entire bad contact. At the same time, there are a lot of isolating switch contact pressure can be adjusted, if in maintenance adjustment pressure is not enough or each finger to adjust the pressure difference will also appear afore-mentioned phenomena.
-
product
BIM Structural Modeling Services
Structural Modeling represents the digital replica of structural components of a building i.e., beams, columns, torsion, and foundations, using Autodesk Revit software. Tejjy-BIM Inc. provides Revit Structural BIM design-drafting-modeling services for concrete & steel structure building design. Integration of BIM modeling in structural engineering facilitates better analysis of design detailing and simulates the behavior to coordinate and collaborate with the architectural & MEP (mechanical, electrical, and plumbing) system. BIM services in structural engineering facilitates structural analysis, and optimization of building design, as well as generate fabrication and construction documents.
-
product
Motor Armature Tester
DS720
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of motor armature with any number of communator bars, for example, automotive motors, motorcycle starter motors, Power tools motors, traction motors, vacuum cleaner motors, fitness equipment motors.
-
product
Insulation Testers
The Zeta series consist of the insulation testers. Zeta series insulation testers have proven invaluable in the testing of insulation resistance measurement for industrial applications such as motors, electrical panels, cables, telecom industry, defense and many more.
-
product
Analogue Instruments
Devices for installation in control, command and distribution panels. A needle on a gauge allows users to quickly interpret the electrical parameters. Analogue devices provide for fast, visual management, without having to interpret the data in order to determine the status of the installation.
-
product
Anti-Condensation Heaters
Anti-Condensation Space Heaters are designed to maintain the temperature of an electrical enclosure. Anti-Condensation Heaters are used for elimination of water vapor contained inside the enclosures. They also provide frost protection by keeping the internal temperature of electrical enclosure above the freezing temperature. The Anti-Condensation Space (Panel) Heaters prevent condensation through convection.
-
product
Moisture Management Tester
Sataton Instruments Technology CO., Ltd
Moisture management tester (MMT) is the tool for the measurement, evaluation and classification of liquid moisture management properties of textile fabrics. By testing the changes in electrical resistance of textiles placed between two horizontal electrical sensors with concentric pins, the tester can calculate fabric liquid moisture content changes that quantify dynamic liquid moisture transport behaviors in multiple directions of the specimen. The software of tester can grade the liquid moisture management properties of a fabric by using the predetermined indices. The tester is used to determine the liquid moisture management properties of knitted, woven and nonwoven textiles, and also can be used to test the one-way transport capability of diapers.
-
product
3-phases Power Analyzers
PeakTech Prüf- und Messtechnik GmbH
s a power analyzer with a large LCD display. Measured power can be recorded with the analyzer, but it is also possible to record and display various voltages, currents, power factors and many other variables. Several electrical variables are attracted during a measurement, so it is possible to show the power and the cos φ at the same time.
-
product
Insulation Resistance Testers
UEi Test & Measurement Instruments
Measures the total resistance between any two points separated by electrical insulation.
-
product
Vibration Unit Tester
BK2020B
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versatile. It can be set up as a stand alone machine, or used with a PC and software for access to more information, and to save the data for analysis. Either version is great on the product line but you may also use it for QA, QC and development.
-
product
Piezoelectric Testing
Radiant Technologies, Inc. specializes in the measurement of electrical and piezoelectric properties of non-linear materials. The Piezoelectric Task captures a sample's displacement as a function of voltage profile along with the sample's polarization response. An external displacement measurement instrument must be attached to a Radiant Precision Test System to make this measurement. All of the Radiant testers are equipped with a high-impedance voltage input to capture the output of a displacement sensor. Every Vision measurement task will collect data from that sensor input simultaneously with the measurement being executed. Radiant's test systems work easily with displacement sensors which include:
-
product
IEC60335 Standard Electrical Temperature Tester
CX-w15
Shenzhen Chuangxin Instruments Co., Ltd.
Standard Test corner/room conform to IEC60335-1:2004. and GB4706.1-2005. can be used to the temperaturetest of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.
-
product
Temperature Calibrators
We offer temperature calibrators in different shapes. We offer temperature dry blocks that can generate an accurate temperature, for example for temperature sensor calibration. We also offer electrical temperature calibrators that can measure and simulate various temperature sensors (RTDs and thermocouples). We also offer high-accuracy reference temperature probes.
-
product
Digital Electrical Network Analyzer
4126 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 Characters LCD.● Auto-ranging / Auto-off.● One Push Button Operation.● Low Consumption.● Better than 3% Accuracy(0.05-50Ω).● Wiring Integrity Check(display + LEDs).● Over temperature protection and indication.● Stores previous readings.
-
product
160-Position QFP-to-PGA Adapter
96-160M65
QFP to PGA Adapter for 160 Position, .0256 [.65] Pitch. Convert surface mount QFP packages to a 15 x 15 PGA footprint. Reduce costs by using less expensive QFP packages to replace PGA footprints in existing designs. Pins are mechanically fastened and soldered to board using Aries patented process, creating a reliable electrical connection and rugged contact.
