Filter Results By:
Products
Applications
Manufacturers
- LBA Group, Inc
product
MW AM Broadcast Mobile Antenna System
TUP-3
The TUP-3 system is capable of transmitting efficiently at carrier frequencies from below 1000 kHz to over 1700 kHz. It is rated for power to 5000 watts, 125 percent modulated. Housed is a weatherproof cabinet, the integral tuning unit features high quality electronic components and matches the TUP-3 system to a 50 ohm transmission line. The self-supporting design of the tower also minimizes erection time and complexity.
-
product
Analog DVR
Sylo Vision Technology Co., Limited
Security cameras capture an analog video signal and transfer that signal over coax cable to the Digital Video Recorder (DVR). Each camera may be powered by plugging in the power supply right at the camera or by using RG59 Siamese cable which bundles the video and the power cables. The DVR converts the analog signal to digital, compresses it, and then stores it on a hard drive for later retrieval. Intelligence is built into the DVR to handle such things as scheduling, motion detection, and digital zoom. Monitors for viewing the video are connected to the DVR, or it can be set up to publish over an internal network for viewing on PCs. The DVR can also be set up to broadcast over the Internet and can add password protection and other features. When broadcasting over the Internet, the video for all of the cameras is transmitted as one stream (one IP address). Therefore, it is very efficient.
-
product
Advanced Test Platform
980 12G
The Teledyne LeCroy quantumdata 980 12G-SDI Video Generator / Analyzer module supports video and audio functional testing of next gen broadcast monitors, conversion devices and sources up to 12G-SDI. The module is equipped with four (4)12G-SDI-capable output ports. The output ports can be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. A genlock input supporting both SD analog black burst and HD tri-level to sync the output clocks with a "house sync" but the module can also run off its internal clock. The module's four (4) SDI input ports can also be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. For single link operation only port 1 on the input or output is functional.
-
product
Test Card Generator
TCG1
This generator provides a standard 75O, 1-volt p-p; PAL encoded CCIR video signal for the testing of monitors and other CCTV equipment. The Test Card Generator TGC1 may display one of four test patterns , (i) Colour bars with reference, (ii) Red Raster, (iii) Peak White Raster and (iv) Composite Test Card (see picture below). The Test Card Pattern incorporates many of the attributes of broadcast test patterns for the evaluation and setting up of CCTV video equipment.
-
product
SpaceWire Monitors
This section details the 4Links range of high-performance test equipment that is used to monitor SpaceWire networks. These devices are attached to your SpaceWire systems and then can be accessed via Gigabit Ethernet, using the standard TCP/IP family of protocols, so that they can be controlled remotely (for instance, by partners collaborating on a mission).
-
product
Broadcast Filters UHF
RFS Waveguide UHF filters are now 4th generation products designed for global combining and filtering applications associated with DTV and analog television transmissions.
-
product
Monitors
The Gentec-EO monitors come in various sizes and types to cover all applications. We have monitors with or without display (PC-based) and for power or energy readings, or both. We also offer the fastest digital needle display on the market.
-
product
Real-Time Broadcast Analysis
Mediaproxy provides a comprehensive suite of software-based analysis applications to help you attend to on-air issues quickly and resolve them efficiently. Employing the latest user interface technologies, complex analysis tasks are made easy and seamless, including your mobile devices.
-
product
Broadcast Combiners
RFS offers a comprehensive product line of FM combiners to suit a wide range of applications. The balanced (or constant impedance) bandpass design offers an expandable system that is built in a modular form enabling extra stations to be added at a future date. This configuration provides state of the art performance with the best frequency response and isolation attainable.
-
product
BROADCAST PROBE
VB120
The VB120 BROADCAST PROBE is a blade based platform for continuous digital TV monitoring, its modular concept providing the flexibility needed for a cost-effective surveillance system tailor-made for each operator. System scalability in terms of monitoring capacity, signal formats handled and functionality ensures a future-proof solution, an invaluable asset in an ever changing world.
-
product
Digital Broadcast Analyzer
Spectrum Analyzer: 9 kHz 4 GHzInterference Analyzer with Interference MappingHigh Accuracy Power Meter, 2-port Transmission MeasurementsCoverage Mapping, Channel Scanner, GPS, AM/FM/PM Analyzer3GPP, 3GPP2, WiMAX, signal analyzersTracking Generator: 500 kHz 4 GHzDigital TV ISDB-T, DVB-T/H analyzersCPRI RF MeasurementsField-proven design: Three-hour battery life, rugged, compact, lightweight, daylight viewable displayIntuitive menu-driven touchscreen user interfacePIM Alert (a downloadable easyTest script)Standard three-year warranty (battery one-year warranty)
-
product
Monitors
Whether you need a local display, alarm and shutdown capability, data recording, and the ability to communicate using Modbus over Ethernet TCP/IP; or you need to trend waveform and transient data to provide a predictive look at your machine’s condition, Metrix has a solution to meet your machinery monitoring requirements.
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Radiation Portal Monitors
SaphyGATE G is an easy-to-use Radiation Portal Monitor optimized for truck, train and cargo radiation control. It's based on large surface, high volume plastic detectors providing the highest sensitivity.
-
product
Temperature/Humidity Monitors
Together, an environment's temperature and relative humidity (RH) indicate how comfortable it "feels" to humans. General sells a variety of temperature/humidity monitors that either show real-time readings like the A600FC High Temperature Analog Humidity-Temperature Meter or log measurements over time for trending purposes such as the HT50 USB Temperature-Humidity Data Logger. Trend analysis is the rationale for another popular application for temperature/RH monitors - water damage restoration.
-
product
Heat Stress Monitors
Heat stress management is often viewed as time-consuming and complex. Simplify your heat stress management with TSI’s intuitive QUESTemp° Series Heat Stress Monitors.
-
product
Broadcast Filters FM
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
product
RF Power Monitors
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
product
RF Power Monitors
Bird's RF Power Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
product
Charge Plate Monitors
Our easy-to-use charge plate monitors allow you to accurately evaluate air ionization systems used to neutralize static charge accumulation. Benefit from our economical solutions and products that offer onboard data storage to automate ionization system testing.
-
product
X-Ray Beam Monitors
When standard products just aren’t good enough—or the measurement technology does not yet exist—Sydor Technologies develops technology to enable these complex imaging measurements. Just as we’ve developed next-generation streak cameras and x-ray detectors to meet novel, emerging requirements in national laboratories, we’re doing the same with x-ray beam monitors.
-
product
Waveform Monitors
LV5300
The LV5300 is a waveform monitor with a 7-inch touch screen display in a compact 3 U enclosure operative with battery power supply.
-
product
Area Monitors
Provides real-time remote radiological monitoring. Local readout of hand-held meter allows for use as a portable survey instrument. More importantly, since the probe’s sensitive electronics are located far from the high field (25 to 350 feet away), they are not subject to destructive gamma exposure. The probe head may be placed directly into a filter compartment or against a resin tank or waste liner.
-
product
Power Monitors
Analog Devices’ power monitoring amplifiers provide an integrated solution for digital current and voltage measurement via an on-chip, 12-bit analog-to-digital converter (ADC), communicated through an I2C interface. Leveraging ADI’s precision analog design techniques, ADI’s products are twice as precise as competing devices, offering best-in-class accuracy (<±0.8%). The power monitors complete the industry’s only monitor and sequencer family to deliver <±1% accuracy for 2 to 12 supplies.
-
product
AC Voltage Monitors
NAI's AC- and DC-powered AC voltage monitors are used to monitor and measure voltage characteristics of single- and three-phase power lines. Field-adjustable AC voltage monitors are also available. These monitors are specifically designed for rugged defense and industrial applications.
-
product
Aerosol And Dust Monitors
TSI DustTrak™ II and DRX Aerosol Monitors are light years ahead of any other. The DustTrak DRX Monitor, for instance, simultaneously measures both mass and size fraction – something no other dust monitor can do. Measure PM1, PM2.5, respirable, PM10 and PM Total simultaneously with no need for size-selective inlet conditioners. When it comes to work comfort and productivity, as well as risk management, don’t you want the best?
-
product
Surface Contamination Monitors
Small-sized devices for measuring the ambient dose equivalent rate and the ambient dose equivalent of X-ray and gamma radiation, as well as measuring the flux density of beta particles (AT6130).
-
product
Monicon Gas Monitors
Monicon Gas Monitors are innovative, cost-effective, wall and rack mounted units, with the ability to monitor single or multiple channels. Before ordering, customers can select from a range of toxic gases, combustible gases and oxygen, for monitoring in a wide range of applications.
-
product
Indoor Air Quality Monitors
Maintaining proper indoor air quality (IAQ) has only become more important in recent years as personal health and comfort have become a higher priority than ever before. Our testing and monitoring instruments for IAQ, including our indoor air quality monitors, gas monitor, and odor meters help industrial hygiene and HVAC professionals test and monitor environments to solve crucial air quality problems.
-
product
Transmitter Monitors Carbon Monoxide
CO-R
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
product
Single Phase Powerline Monitors
a Voltage disturbance detector and recorder. This device is designed to be plugged into a 120V or 240V AC line and will monitor this line for voltage disturbances and temperature or Humidity variations.
