Filter Results By:
Products
Applications
Manufacturers
ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
- TEAM SOLUTIONS, INC.
product
16-bit, 400KHz, 4 Isolated Analog Differential Inputs, Simultaneous Sampling
APCI-3003
With the new fast A/D converter board APCI-3003, the user can achieve high data transfer rates by a simultaneous conversion of 4 channels at once. The board has 4 differential input channels. Each channel has its own A/D converter. The transfer rate can be set in a flexible way from 100 kHz for each channel, when 16 channels are set, to 400 kHz for each channel, when 4 channels are set. All 4 channels are optically separated from each other up to 500 V.
-
product
16 Channel Charge Integrating ADC
CQ16
The CQ16 is a 16-channel 12bit, fast converting charge-integrating ADC for CAMAC. To provide compatibility to older CAMAC ADC’s it can be switched into an 11-bit mode. All data read-out is provided either via CAMAC commands or through the fast FERA bus on the front of the module.
-
product
8-Channel VME LVDT/RVDT Scanner
V550
The V550 is a 6U, one-slot VME module which will acquire position data from up to eight LVDT (linear variable differential transformer) position sensors. The LVDT sensors are excited by an ultrastable synthesized sinewave generator, and conditioned by a precision 16-bit A/D converter followed by digital signal processing. The resident microprocessor supervises scanning and signal conditioning, and places updated position data in VME-accessible dual-ported data registers for instant access from the VME bus.
-
product
2 Channel 1GSPS 8 Bit ADC Card in FMC
FM582
Sundance Multiprocessor Technology Ltd.
The offset adjustment does not clip the signal at the highest range (+/- 5V). That is why the “max input signal amplitude” has been specified as 10V, even though the selection of signal ranges only goes up to 5V. This way, a +10V pulse with -5V offset could still be digitised without clipping.
-
product
PXIe-4305, 24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module
783868-01
24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module—The PXIe‑4305 is a filtered analog input module for higher voltage measurements. The module offers the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
RH850 Family (Automotive only)
RH850/E2x
RH850/E2x microcontrollers are ideal for powertrain applications, have high operation processing performance for realizing new combustion systems for fuel-efficient engines, and built-in hardware for knock control such as a successive approximation A/D converter, delta-sigma A/D converter, cyclic A/D converter, Digital Filter Engine (DFE), and Advanced Timer Unit (ATU-V), and engine control such as fuel injection control.
-
product
Mini Liquid Level Sensor
28090
The Mini Liquid Level Sensor is made to be inserted vertically into wet environments to detect liquid level from 0 to 1.88” (48 mm) or as an alarm. This sensor has a single analog output which may be directly connected to the Propeller Activity Board 4-channel A/D converter or easily interfaced with the MCP3002 A/D with a FLiP Multicore Microcontroller.
-
product
PXI Express Board Virtex-5 ADC Module
SMT742
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
product
Audio IP
We provide high-performance, compact, low power and customizable audio analog mixed-signal IP in leading foundry processes, including a wide range of ADC, DAC, CODEC and Voice Activity Detectors.
-
product
PXIe-7847, Kintex-7 160T FPGA, 500 kS/s, DRAM PXI Multifunction Reconfigurable I/O Module
784144-01
Kintex-7 160T FPGA, 500 kS/s, DRAM PXI Multifunction Reconfigurable I/O Module—The PXIe‑7847 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7847 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7847 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PXIe-7865, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787355-01
PXIe, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7865 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7865 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 160T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7865 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Plus 16 Digital Channels
MSOS404A
4 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
PCIExpress Kintex UltraScale FPGA Carrier Board
PCU: 085/115
The PCU continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD Kintex UltraScale FPGA computing power. The PCU is a PCIExpress, standard form factor , FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications at a competitive price point. AMD Kintex UltraScale XCKU085/115 delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PCU FPGA node processes input from the FMC HPC +(Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 12.0GSPS).
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-02
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
DUAL RF Multiple-Input/Output
FMC-SDR400
Sundance Multiprocessor Technology Ltd.
FMC-SDR400 is a Dual RF multiple input/output module (MIMO) based on AD9361, 70MHz – 6GHz RF transceiver and AD9656 ADC for baseband sampling of less than 70MHz (input only in this range). A software selectable gain and tunable RF bandpass front-end section provides high RF sensitivity by allowing rejection of out-of-band-of-interest interfering signals.
-
product
RA Family Of Arm-based MCUs
RA4
The RA4 Series bridges the needs for reasonable low power with the demand for connectivity and performance. These MCUs deliver up to 48MHz of CPU performance using an ArmⓇ CortexⓇ-M4 core with up to 256kB of embedded flash memory. The series offers a wide set of peripherals, including USB, CAN, ADC, capacitive touch, a segment LCD controller, and additional security IP integration, making it suitable for industrial equipment, home appliances, office equipment, healthcare products, and meters.
-
product
8-Channel ADC Module
FMC168 – LPC
Sundance Multiprocessor Technology Ltd.
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250 Mega samples per second sampling rate per channel. With a flexible clock generation and distribution scheme, the FMC168 allows control on sampling frequency and analog input gain through serial communication with a carrier card. The FMC168 design is based on the TI ADS42LB69 Dual Channel 16-Bit 250 MSPS A/D, is equipped with power supply and temperature monitoring, and offers several power-down modes to switch off unused functions.
-
product
PowerPC 405 Board
MS 1533
- Virtex 4 FPGA with Embedded PowerPC 405 (PPC405) Core- Up to 450 MHz operation- Tri-mode Ethernet Media Access Controller- A/D Converter Blocks (10-bit / 200 kilo samples per second)- Select IO Technology (Wide selections of I/O standards from 1.5V to 3.3V)- DDR2 SDRAM (256MByte)- Program Storage Flash Memory (8MByte)- Data Storage Flash Memory (8MByte)- Vertex-4 FPGA PROM (4MByte)
-
product
ADC DAC Module
ZET 230
ZET 230 ADC DAC module is used for high-precision signal measurements in wide dynamic and frequency range. The module has an integrated anti-aliasing filters for 25 kHz. ZET 230 ADC DAC module is not designed for digital processing of constant level signals.
-
product
FlexRes® Oscilloscopes
PicoScope® 5000 Series
High speed and high resolution. Breakthrough ADC technology switches from 8 to 16 bits in the same oscilloscope.
-
product
Delta-Sigma A/D Converters
Renesas offers several delta-sigma and sigma-delta analog-to-digital converters for high resolution measurement applications.
-
product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
Data Acquisition
Data Acquisition module incorporating 16 Analog-to-Digital (ADC) inputs, 8 Digital-to-Analog (DAC) outputs, and 48 bi-directional Digital I/O in a single module.
-
product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
Virtex 5, PXI Express, 125MHz ADC
SMT784
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or SXT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2233-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
16 Channel ADC for CompactPCI
CPCI392
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
product
Services
ADC Channel Listening
The program is used for listening to signals coming to the input channels of ADC modules and FFT Spectrum Analyzers.
-
product
8-Channel 250 MHz A/D Jade XMC Module w/ 72 DDCs for Defense & Radar Phased-Array Applications
member of the Jade" family of high-performance data converter XMC modules based on the Xilinx Kintex Ultrascale FPGA. The Model 71132 is an XMC module featuring eight 250 MHz 16-bit A/Ds with eight wideband digital down converters (DDCs) and 64 multiband DDCs, all fully programmable. The Model 71132 doubles the number of A/D channels and DDCs over previous models giving this the best price per channel ratio in the product family. Applications monitoring a broad spectrum with a need to quickly analyze specific portions of the identified spectrum can greatly benefit from the capabilities of the 71132.
-
product
Signal Analysis
FFT Analysis
The program FFT (Fast Fourier Transform) Analysis is used for narrow-band spectral processing of signals coming from the input channels of ADC modules and FFT spectrum analyzers (in real-time or recorded time realization view mode), as well as for viewing various spectral characteristics of signals.
