Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Tool, Kit, High Power, Receiver and ITA, Crimp
910102117
This tool crimp kit contains the specific locator and die set for 2 AWG High Power contacts.
-
product
50/75 Ohm Micro Coax Contacts
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
product
Crimp Force Monitor
638007950
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
product
Coax, Contact, Receiver, 75 Ohm, RG179
610104157
Primary mating contact 610103169. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact - 5 mΩOuter Shield - 3 mΩCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Wire Crimp Pull Tester (Manual)
WT3-201
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
product
Coax, Contact, ITA, 75 Ohm, RG179
610103169
Primary mating contact 610104157. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield - 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact is 5 milliohms Outer Contact is 3 milliohmsCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Crimp Tester
TF125
TESTEX Testing Equipment Systems Ltd.
Crimp Tester, to calculate the crimp in yarn affected by knitting or weaving by taking apart the yarn from a piece of given-length fabric, unbending it under given force and measuring its length, to determine actual yarn usage.
-
product
Wire Crimp Pull Sensor
Model MR06-200
The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the handles together to increase tension on the sample until a break occurs. The peak force is recorded by a Mark-10 indicator. A rotating turret with slots of multiple sizes accommodates a wide range of wire diameters, up to 0.25 in. (6.4 mm).
-
product
Wire Crimp Pull Tester (Motorized)
WT3-201M
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body (RCV) – BeCu (Twin Female)BeCu/PhBrz (Crimp)Male (ITA) – BrassContact Plating Female (RCV) – 50µ” Au over 100µ” NiMale (ITA) – 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Force Transducers
Metra Mess- und Frequenztechnik in Radebeul e.K.
Piezoelectric force transducers are suited for the measurement of tensile and compression force.
-
product
Crimp Tool DIN 41612
40-964-160-C
A DIN 41612 Crimp Tool suitable for making crimped terminal connections to individual wires and cables. Please see our product 40-964-160-E for the Connector Pin Extractor Tool.
-
product
Atomic Force Microscope
AFM Heron
New, fully motorized AFM HERON (HERO of Nanotechnology) which allows to perfectly align a cantilever, laser and photodiode by just one click on a command button. The scanning settings and landing parameters are also automated that allows to avoid any time consuming adjustment operations, thus leaving more time to researcher for designing the experiment and performing more accurate measurements.
-
product
Sauter Force Gauges
Force gauges provide a quick and reliable way to obtain a measure of force in tension and compression. DMV UK offer a comprehensive range of mechanical and digital force gauges with selectable units and peak force capture with capacities from 2 N to 100,000 N. All gauges are supplied with standard accessories, a 2 year warranty, and can be used for force testing in hand held or test stand applications.
-
product
Force Tensiometers
Sigma 700/701
The outstanding versatility of Sigma 700 and 701 force tensiometers makes them suitable for research and development, industrial quality control, routine measurements as well as academic research. Both instruments are computer controlled and have a high level of automation.
-
product
Force Sensors / Force Transducers
HBM force sensors and force transducers measure static and dynamic tensile and compressive loads - with virtually no displacement. Your force load cell can be supplied in the most varied of designs and classes of accuracy. Typical force measurement application areas include bench testing, e.g. force measurement to check material quality and automation technology, e.g. for monitoring quality during reshaping or bonding operations.
-
product
Peel Force Tester
PT-55
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
-
product
Force Gauges
A digital force gauge, often called a push pull force gauge or tension and compression force gauge, is used in material testing, quality control and assurance, research, development, product testing, laboratory and educational applications. PCE Instruments' (PCE) digital force gauge products are the benchmark of quality and performance. PCE digital force gauge devices provide measurements in kilograms (kg), grams (g), ounces (oz), pounds (lbs) and Newtons (N) of force (f), depending on the force gauge model. Most PCE digital force gauge products are handheld, portable devices that also can be used with a universal test stand. There are several different force gauge products available online in the PCE web shop.
-
product
Atomic Force Microscope
NX-Hivac
Park NX-Hivac allows failure analysis engineers to improve the sensitivity of their measurements through high vacuum Scanning Spreading Resistance Microscopy (SSRM). Because high vacuum scanning offers greater accuracy, better repeatability, and less tip and sample damage than ambient or dry N2 conditions, users can measure a wide range of dope concentration and signal response in failure analysis applications.
-
product
Radiation Force Balance
Radiation force balance for diagnostic and therapeutic medical ultrasound
-
-
product
Force Sensors
TE Connectivity (TE) designs and manufactures force sensors for applications that require high performance or unique packaging, including electro-mechanical flight control, test and measurement and ultra-low cost OEM load cells for medium to high volumes. Based on our proprietary piezoresistive silicon strain gage (Microfused) technology, our sensors combine durability and long-term stability in extremely low cost packages.
-
product
Wire Crimp Testers
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
product
Atomic Force Microscope
XE7
Park XE7 has all the state-of-the-art technology you've come to expect from Park Systems, at a price your lab can afford. Designed with the same attention to detail as our more advanced models, the XE7 allows you to do your research on time and within budget.
-
product
Press Force Load Cell
6000 Series
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
product
Tool, Crimp, 75 Ohm Coax, Receiver and ITA, Hex Crimp
910104139
Used to crimp the ferrule on 75 Ohm contacts. Also included in tool kit p/n # 910102107.
-
product
Force Sensors
Piezoelectric force sensors, respectively piezoelectric force transducers or load cells, are perfectly suited for the precise measurement of compressive and tensile forces, both in highly dynamic applications and in quasi-static processes. In universities and industry, for basic research or quality assurance: exact data is always essential in order to measure force characteristics and make processes more cost-effective. Thanks to their rugged design, piezoelectric force sensors from Kistler keep precise track of quasi-static and highly dynamic force processes, even when conditions are difficult. Our force sensors can also handle simultaneous measurements of multiple orthogonal force components.
-
product
Force Tensiometer
K20
Our Force Tensiometer – K20 is a robust, semi-automatic instrument for the precise measurement of surface tension and interfacial tension. Using the ring and plate method as the main tensiometric methods, it produces reliable measurements for the routine quality assurance of your surfactant solutions and interfacial processes.
-
product
Force Distance Tester
925
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
product
Atomic Force Microscope
AFM
Atomic Force Microscopes are the most widely used SPM microscopes. They can be applied in fields that span from surface science, semiconductor technology, magnetic media, polymer science, optics to biology, chemistry and medicine.Absolute positioning with an accuracy of 2 nm.
