Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
ARINC 429 Test And Simulation USB Module
USB-429
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
product
Multi-Channel, Multi-Protocol 1553 and ARINC 1/2 Size PCIe 4-Lane Interface Card
PCIEC4L-MA4
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
ARINC 429 Test And Simulation VME Module
VME-429
*8, 16, 32 or 64 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Next Gen ARINC 615-3/615A Portable Data Loader
Model No. 11615-50
Aero Instruments & Avionics, Inc.
The Aero Instruments & Avionics 11615-50 Portable Data Loader (PDL) provides proven ARINC 615-3/ARINC 603 load technologies with additional ARINC 615A over Ethernet capability. This new addition to our product line is ideal for aircraft fleets preparing to use, or that are currently using 615A loadable equipment. Avionic data loads can be performed from Floppy Disk, CD, DVD, USB, or the internal solid state Mass Storage Device (MSD). The MSD can be loaded in advance to eliminate the distribution of disks/memory devices to airplanes while significantly reducing the time to perform the data load tasks. External media is verified before any load is executed. This saves valuable ground time by alerting the operator of any bad media before attempting the load. Our 11615-50 PDL is easy to read and easy to use. All functions are performed using the high resolution 5” TFT LCD display and four large “Soft Buttons”. Together, they provide simple navigation to the selected loadable software and straightforward load status messages. Call Jim Krey for a quote: 716-694-7060 ext. 322
-
product
ICE 3000 Series
ICE3009
The ICE3009 subsystem is an agile filter for the VHF-L, VHF-H and UHF frequency bands. It allows operation of a number of transceivers in a cosite environment. The VHF/UHF Filter provides multiple poles of RF selectivity to reduce broadband noise in transmit mode of operation and to reduce interfering signals at the transceiver’s RF input in receive mode at Have Quick II/IIa and SATURN tuning speeds. This design incorporates a flexible control scheme that can be configured at the factory for various radio interfaces (ARC-210, ARC-231, ARINC 429, etc.). The design is highly integrated and includes all filters, amplifiers, power supply, transmit and receive switching (including a bypass mode), and Built-in-Test (BIT). A mounting tray is available as an option for easy incorporation on your platform. This system is qualified for military applications. Cost-effective modifications are available on the ICE3009. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
Ethernet & NLINE: Real-Time 1553 & ARINC Converter/Bridges
Alta’s Ethernet (ENET & NLINE) Avionics converters are the first and most unique Ethernet appliances in the industry. A real-time UDP server engine (no IP software stack like most other products on the market) provides direct data buffer and transmission control of MIL-STD-1553 and ARINC-429 interfaces.
-
product
Quick Access Recorders
QAR
Two QAR styles are available depending on the features needed, both include our specialized Silo™ Quick Access Recorder Software. Silo QAR with webFB hardware is the ideal certified solution for programs on Boeing 737 aircraft. It quickly attaches to the Flight Data Recorder (FDR) test receptacle and gathers data using the ARINC 717 protocol. For applications on other aircraft or using other protocols, Silo QAR with webCS hardware includes ARINC 429 and Discrete interfaces in addition to ARINC 717.
-
product
ARINC 818 Analyser
iWave’s ARINC 818 Video Protocol Analyzer (VPA) instantly verifies the ADVB Packets against ARINC818 Standards. ARINC818 VPA software efficiently captures, decodes the ADVB data, and displays the ADVB data, raw video data, and error status. It is an excellent troubleshooting tool that helps to quickly detect and rectify errors in the ARINC 818-2 applications, simultaneously ensuring compliance of the system with the ARINC 818-2 standards.
-
product
3U cPCI 8 Channel ARINC 429 Module
DP-cPCI-4296
DP-cPCI-4296 board features cPCI based eight channels ARINC429 protocol interface. As part of the cPCI family, the DP-cPCI-4296 board is fully compliant with compactPCI® specification 2.0 R3.0. and CompactPCI® Hot Swap Specification 2.1 R1.0.
-
product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
product
EMI/EMP Connectors
Filter connector series includes EMI/ EMP/ESD circular, ARINC, D-subminiature and micro-D connector styles. They can be combined with high energy TVS diode technology to achieve lightning and EMP transient protection. Smiths Interconnect's EMI filter connectors use multi-layer ceramic capacitor arrays together with inductive materials to realize robust, high performance low pass filter networks. Where required, transient protection can be combined with EMI /RFI filtering to provide maximum protection. The diodes as well as the EMI filter are packaged separately so the construction of the connector remains modular.
-
product
Shop, Bench-top 615-3/4 Data Loader
F-SIM-LDR-615
Avionics Interface Technologies
An ARINC 615-3/4 compliant Data Loader software package that includes an easy to use, intuitive, software data loader user interface and command line interface.
-
product
Multichannel Memory-Mapped ARINC 708/453 Interface Card
EXC-708mPCIe
The EXC-708mPCIe is a multichannel, memory-mapped ARINC 708/453 interface card that supports two ARINC 708/453 channels, each programmable as transmit or receive. Each channel implements a 64K x 16 FIFO and supports polling and/or interrupt driven operation. The card complies with the PCI ExpressTM Mini Card standard. It’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 708 interfaces and for performing system simulation of the ARINC 708/453 Weather Radar Display databuses, both in the lab and in the field. In Transmit mode, each ARINC 708 word is written to the FIFO as a block of 100 16-bit words. In Receive mode, each ARINC 708 word is stored in the FIFO as a block of 103 16-bit words. The first two words comprise the 32-bit Time Tag, indicating the word’s time stamp. The next 100 words comprise the 1600 bits of the ARINC 708 word, which are followed by the Status Word.The EXC-708mPCIe card comes complete with C drivers including source code.
-
product
ARINC HSI / ADI Test Fixture
TA-2000
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
product
ARINC Interface Cards
- Wide Selection of COTS ARINC Interface Cards/Boards and Real-Time Appliances- 4-48 Shared and Dedicated, Independent RX/TX Channels- Portable FPGA AltaCore Design – Reduced Parts Obsolescence Risk- Most Advanced Error Detection and Injection Available- Parametrics Variable Voltage on ENET-A429P
-
product
ARINC 429 Interface CPCI Card
RAR-429 Series
The RAR-429 module is a rugged, reliable, full featured, CompactPCI module designed to provide a stand-alone, ARINC 429 interface for avionics applications. Up to 16 ARINC429 channels are supported on a 3U CompactPCI module. The RAR-429 offers full functional test, simulation, and monitoring for ARINC 429 test and simulation applications.
-
product
PXI ARINC 608A Switch Modules
The matrix module is based on our proven BRIC format and can be specified as a 4 or 8 slot module. The module can be fitted with a combination of Resource Distributor and Bus Matrix Input daughter cards as required by the user. The maximum configuration is six Bus Matrix and two Resource Distributor cards fitted in a BRIC8 module.
-
product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Data Acquisition - 3U 3-Slot
DAQ-33CP0G
is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of military/aerospace data acquisition applications that require high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications Dual-Port Gig-E Ethernet.
-
product
Aerospace and Defense Software (3000A/T/G X-Series)
D3000AERB
MIL-STD 1553 and ARINC 429 triggering and analysis for the InfiniiVision 3000A, 3000T, 3000G X-Series oscilloscopes, along with mask testing, advanced math, video analysis, and more.
-
product
Converter
ARINC 429
ARINC 429 runs at one of two speeds – 100KHz or 12.5 Khz (nominal). But, the Russians have created an 'ARINC 429 like' standard, which operates at ~ 50KHz. Our customer needed to convert the 50 Khz 'Russian ARINC' to standard high speed ARINC 429, so that their existing test rig would accept it. Our solution all fits in this very small enclosure.
-
product
Portable Testing Kit for Gulfstream Aircraft
ES-429TK-101
The ES-429TK-101 Portable Testing Kit (for Gulfstream aircraft) enables you to simulate Airspeed, Altitude and Radio Height values over an ARINC 429 bus. The ES-429TK-101 Portable Testing Kit consists of a DAS-429UNET/RT10, battery and the Exc429Tester application that runs on the host computer, a laptop or desktop PC running Windows. Using the ES- 429TK-101 Portable Testing Kit with a laptop provides a portable testing system.
-
product
Development Switch
AFDXSwitch Lab v2.0
The AFDXSwitch Lab v2.0 is identical to the TTESwitch A664 Lab v2.0, which fully supports AFDX® and operates in accordance with all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally, the switch comes with advanced features like 1 Gbit/s speeds and flexible physical layer configuration. The TTESwitch A664 Lab v2.0 is based on the TTESwitch Module A664 Pro, thus providing the full range of technical functionalities of TTTech’s certifiable AFDX switch modules and making it the optimal switching solution for a large variety of different application areas.
-
product
4 or 8 Channels In-Line Real-Time ARINC-Ethernet Converter
NLINE-EA429
NLINE-EA429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). NLINE-EA429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
product
Rugged Rectangular Fiber Connectors
TE Connectivity (TE) has a range of rectangular fiber connectors for rugged environments including the ARINC and MTCT connectors. Whether you are designing collision avoidance systems, in-flight entertainment, or air-to-ground communications, you face a challenging economic environment and an ever-increasing demand for weight reduction. TE's ARINC 600 next generation receptacle connector allows you to reduce both weight and costs. TE's MTCT connector is a compact, lightweight design connector for use with ARINC 801 fiber optic termini. Ideal for applications such as avionics, in-flight entertainment systems, communications, production breaks and other areas.
-
product
Multi-Channel, Multi-Protocol ARINC Ethernet Appliance
ENET-MA4
eNet-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNet-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 8 ARINC channels.
-
product
FMC Module
NES-FMCA429-CAN
Sundance Multiprocessor Technology Ltd.
The NES-FMCA429-CAN from Nolam embedded systems is the world’s first FMC module combining ARINC ‘429 bus and CAN bus in a single FMC module. The NES-FMCA429-CAN features 2 receive and 2 Transmit ARINC429 channels and CAN bus. Both protocols have Autotest capabilities.
-
product
ARINC 429 Test & Simulation Interface for VME
VME-429
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
ARINC 708 Video Distribution Units
AB2-VDU
The AB2-VDU is easily deployed and ready to operate in the most challenging environments. The unit is SWaP (Size, Weight, and Power) optimized in a compact, rugged package for easier integration and longer life.
