Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
product
Compact PCI
cPCI2IP
The cPCI [Compact PCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots.
-
product
Flexible MiniPCI Express Riser
SKU-055-0X
The Flexible MiniPCI Express Riser (Riser) was designed to extend the MiniPCI Express bus. The Riser includes a MiniPCI Express adapter board (downstream), MiniPCI Express host board and a 12” PCI Express flat cable.The MiniPCI Express host board connects to the motherboard MiniPCI Express connector.
-
product
Flexible x1 PCI Express to MiniPCI Express Adapter
SKU-056-02
The Flexible x1 PCI Express to MiniPCI Express Adapter (Adapter) was designed to convert the x1 PCI Express bus into the MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion add-in board to the motherboard PCI Express connector.The Adapter includes a MiniPCI Express adapter board (downstream), x1 PCI Express host board and PCI Express flat cable.
-
product
PMC Carrier with 2 positions
PMC-MC-X2
The PMC-MC-X2 adapter / carrier converter card provides the ability to install up to 2 (two) PMC cards into a small enclosure. The PMC-MC-X2 has one PMC card slot mounted front and rear to create a compact arrangement with 2 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
product
CompactPCI
cPCI4IP
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
product
Flexible x1 PCI Express to PCI Adapter
SKU-041-0X
The Flexible x1 PCI Express to PCI Bus Adapter (Adapter) was designed to convert the x1 PCI Express bus into two 32-bit PCI buses. It allows you to connect up to two 32-bit PCI expansion boards to the motherboard x1/x4/x8/x16 PCI Express connector.The adapter includes a PCI adapter, x1 PCI Express host board and a PCI Express flat cable.
-
product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
product
Rugged Ethernet
ES-1553RUNET/Px(S)
The ES-1553RUNET/Px is an intelligent, rugged single channel, MIL-STD-1553 adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in rugged environments.The ES-1553RUNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
AXIe 5-Slot Chassis
M9505A
The M9505A AXIe Chassis is fully compatible with the AXIe 1.0 specification. It includes an embedded system module (ESM) that does not take up an instrument slot. This system module performs the chassis management functions contained in the AXIe specification. Additionally, it provides PCI and LAN interfaces for connection to an external computer, external clock and trigger connectors, and Keysight-exclusive, inter-chassis synchronization connectors. The local bus implemented in the M9505A provides the maximum 62 pairs allowed by the AXIe specification. Combine the M9505A with the M9048A PCIe Desktop Adaptor to achieve the highest system bandwidth.
-
product
FantASI ASI/SD-SDI Input+output For USB-2
DTU-245
DekTec's classic and iconic portable ASI adapter for USB bus, ideally suited for use with a laptop, but convenient with a standard PC or server too. More than ten years on the market and still the essential tool for every DTV engineer!
-
product
PMC Carrier/Adapter/Motherboard
PMC-MC-X4-RIO
PMC-MC-X4-RIO adapter, carrier, motherboard provides the ability to install up to 4 (four) PMC modules into a small enclosure. PMC-MC-X4-RIO has two PMC card positions top and bottom to create a compact arrangement with 4 PMC positions. X4 is a complete solution with built in power supplies, thermal protection, voltage monitoring, bus arbitration, clock distribution, fan control and more. Compact chassis available to house PMC-MC-X4-RIO.
-
product
Flexible MiniPCI Riser
SKU-068-0X
Flexible MiniPCI Riser (Riser) was designed to extend motherboard MiniPCI bus. The Riser includes a MiniPCI Host board, MiniPCI Adapter board and a PCI Express flat cable.
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
PCI card with 3 IP sites
PCI3IP
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
product
I2C Bus Host Adapters
iPort/AFM 2 brings I2C directly to your Windows, Linux, or Mac OSX PC, Single-board Computers, or Embedded Systems. Just load our free software, plug the iPort/AFM 2 into your computer's legacy or add-on RS-232 port, and you will be sending and receiving I2C Bus messages in minutes.
-
product
Flexible MiniPCI Express to PCI Express Adapter
SKU-035-XX
The Flexible MiniPCI Express to x1, x4 or x16 PCI Express Adapter (Adapter) was designed to convert the MiniPCI Express bus into x1, x4 or x16Express bus and extend it. It allows you to connect a x1, x4 or x16 Express expansion add-in board to the motherboard’s MiniPCI Express connector.The Adapter includes an x1, x4 or x16 PCI Express adapter board, MiniPCI Express host board (full-size or half-size) and a PCI Express flat Cable.
-
product
Flexible MiniPCI to MiniPCI Express Adapter
SKU-054-0X
The Flexible MiniPCI to MiniPCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a MiniPCI Express bus. It allows you to connect a MiniPCI Express board (half-size or full-size) to a motherboard that has a standard 124-pin MiniPCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), MiniPCI host board and PCI Express flat cable.
-
product
Hawk EI Co-Processor
9322 EI
Hawk Co-Processor (Hawk-E) including I/O bus adapter with control logic for DG-compatible I/O devices, two slots required. Supports both Programmed and Data Channel I/O.
-
product
Osprey ISA Q-Bus Adapter board
9476-Q-B
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
product
Flexible x1 PCI Express Riser
SKU-039-XX
The Flexible x1 PCI Express Riser (Riser) was designed to extend the x1 PCI Express bus. The Riser includes an x1 PCI Express adapter board (optional: x4 PCI Express adapter), x1 PCI Express host board and a 12” PCI Express Flat cable.
-
product
PCI to PCI Express Adapter
SKU-011-01
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
product
Carrier Cards and Bus Adapters
Abaco's wide range of carrier cards allows you to expand your systems capabilities simply and cost-effectively, allowing easier technology insertion.
-
product
PMC to PCI Adapters
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
product
SAS (Serial Attached SCSI)
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
product
Kestrel /SX Co-Processor
0149-SX
Same speed Windows/NT Kestrel Co-Processor for equivalent system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.
-
product
I2C High Speed Interface for USB
Tracii XL 2.0
telos EDV Systementwicklung GmbH
Tracii XL 2.0 is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 3.33 Mbit/s. Additionally Tracii XL 2.0 can work as an I2C monitor.
-
product
Osprey ISA Unibus Adapter
9476-U-B
Unibus Controller board is EISA/ISA bus compatible and occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
I2C High Speed Interface for USB
telos Tracii XL
telos EDV Systementwicklung GmbH
Tracii XL is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 2 Mbit/s. Additionally Tracii XL can work as an I2C monitor.
