Filter Results By:
Products
Applications
Manufacturers
-
product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
Handheld instrument for electrical conductivity measurement of non-ferromagnetic metals. The electrical conductivity can be used for determining material properties, like hardness, strength, heat damage and material fatigue of metals. Rapid and simple on-the-spot conductivity measurement of non-ferromagnetic metals acc. to DIN EN 2004-1 and ASTM E 1004.
-
product
Flexural Damage Tester
DRK242A-II
Shandong Drick Instruments Co., Ltd.
It is used to test the dynamic anti-torsion and flexural fatigue performance of coated fabrics.
-
product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
product
CO2 Monitor
T5000
Although carbon dioxide is invisible and odourless, increased CO2 content in the room leads to fatigue and decreased mental concentration.
-
product
High Temperature Clip-On Gages (700 C)
Model 7641
Jinan Testing Equipment IE Corporation
These COD gages use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7641 is ideal for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. All units can be displaced slightly in compression for ease of installation. The COD gage is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the COD gage. This system provides a number of functional enhancements, including: high speed digital output, built in calibration and tare functions, analog and digital filters, and more. The 7641 is readily interfaced with most existing test controllers, and may be directly connected to a data acquisition system or chart recorder, or directly to a PC. The 7641 may be used for strain controlled tests such as JIC.
-
product
Heel Fatigue Tester
UI-FT49
Heel Fatigue Tester is used to test lady shoe heel withstand repeated impacts in daily walking. This heel tester is suitable to test plastic heel and steel heel dowels. Heel Fatigue Test Method includes BS 5131-4.9, ISO 19956, SATRA TM21, QB/T2864
-
product
Torque Arms
Providing ergonomic solutions for your assembly line workers lessens fatigue, prevents injuries, and boosts productivity. Because your workers can complete jobs more comfortably, they'll be happier, and happy workers are more likely to be engaged and less likely to make mistakes. Mountz torque arms take the weight off a tool operator's shoulders so they can guide the tool instead of lifting it, reducing the likelihood of repetitive motion injuries. Torque arms can even absorb the vibrations from power tools. Mobile and flexible, torque arms find a place even in tight workstations and can be reconfigured to take on new assignments. Mountz torque arms help make factories great places to work.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
Hydraulic & Pneumatic Pressure Sensors
One of the toughest applications for pressure sensors is measuring high pressure, repetitive pulses, such as those encountered in hydraulic applications. However, our pressure sensors are designed to continuously measure repetitive pulses during applications such as hydraulic cylinder “torture” testing or diesel fuel injection. Ordinary diaphragm-type sensors usually fatigue quickly in such applications.
-
product
Servo-Pneumatic Asphalt Testing System
All signal conditioning, as well as high-speed data acquisition and control functions are done by the unit and graphically interfaced through CATS, windows based software running on a standard PC. The system is capable of performing the full spectrum of HMA tests: dynamic complex modulus, flow number, flow time, indirect tension, beam flexural fatigue and resilient modulus. These tests are done with the appropriate testing modules. The different testing modules can be obtained after the initial system acquisition at the same discounted price. In addition, guarantees system upgrades in order to meet future standards .
-
product
Demattia Flex Tester
UI-FT33
Demattia Flex Tester & Demattia Flex-Cracking Tester is used to test rubber crack growth under repeated bending or flexing. Unuo manufactures demattia flexing fatigue tester which meets test methods of ASTM-D813, GB/T 13934, HG 2873, ISO 132:1999(E), BS 903-A10 and etc.
-
product
Electronic Product Testers
Infinity Machine International Inc.
Electronic Product Testers by Infinity Machine International Inc. - for applications such as connectors insert and extract testing machine, touch screen torsion, abrupt pull tester for power wire and headphone cable, double station electronic product cable tester, cord flexing rotary bending fatigue tester, button click electronic product tester simulation, and more.
-
product
High Temperature Self-Supporting Furnace Extensometers (1200 C)
Model 3448
Jinan Testing Equipment IE Corporation
Epsilon developed this unique high temperature extensometer for testing metals, ceramics, and composites at the high temperatures produced by furnaces and induction heating systems. A combination of features make these extensometers easier to use and better in performance than other similar high temperature extensometers.The units are held on the specimen by light, flexible ceramic fiber cords. These make the extensometer self-supporting on the specimen. No furnace mounting brackets are required. The side load on the test sample is greatly reduced because of the self-supporting design and light weight of the sensor. Most materials testing furnaces with a side cut-out for an extensometer will readily accept a Model 3448. For induction heating systems, a different ceramic cord placement allows the extensometer to easily pass between the coils.The combination of radiant heat shields and convection cooling fins allow this model to be used at specimen temperatures up to 1200℃ (2200°F) without any cooling. An optional tiny air fan does enhance stability at the highest temperatures and is recommended for the highest accuracy and for tests with small elongations. The fan comes with a magnetic base for support so it can be mounted at any convenient location near the extensometer. Fan cooling is not generally needed for induction heated systems. High purity alumina ceramic rods are used. These are available in lengths as required to fit your furnace. A spare set is included with every extensometer. Specify chisel, vee chisel or conical contact points as desired.Most units operate equally well in tension and compression. Thus tensile, compression and cyclic tests like low cycle fatigue can all be performed with a single unit.For vacuum furnaces, special models are available. Epsilon can also provide a radiant heat transfer cooled version. This requires that the extensometer module be surrounded by a water cooled enclosure with a front slot for the ceramic rods.
-
product
Tensile Test Chamber
CSZ's Tensile Test Chamber is an environmental chamber that interfaces with a customer tensile tester load frame. This chamber is required to expose various materials and components to temperature conditions while undergoing tensile test. Tensile testing stresses materials by pushing, pulling, twisting, or bending intended for static and fatigue testing.
-
product
Fatigue Test Machine
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Built to evaluate the strength of raw materials, components or finished products.
-
-
product
Strain Sensors
Columbia Research Laboratories
Columbia's foil strain sensors monitor the fatigue loading experienced by tactical aircraft under various conditions of speed, weight and missions configuration. Critical undercarriage structures and control surfaces may be monitored for fatigue damage induced by high-G maneuvers and high stress landings. These sensors are self-temperatures compensating, environmental resistant, have a high output, two active arms and are easily installed. Developed for the demanding requirements associated with tactical military aircraft, they are equally useful performing many of the more common strain measurements encountered in the material testing laboratory. Columbia's foil strain sensors are considered the standard for the industry.
-
product
Computer Servo Control Testing Machine for Rock Stiffness
YAW-G300
Jinan Testing Equipment IE Corporation
The Computer Servo Control Testing Machine for Rock Stiffness is used for static fatigue compression test for conncrete & rock material under different parameter. The test includes compression, shearing test, three-point bending testing & fatigue test. Meanwhile, the Computer Servo Control Testing Machine can also realize the automatic control, measuring, data processing; curve analyzing, result displaying and test report printing in the process of various tests. The stiffness testing system can do full process test under stress and strain.
-
product
(25kN) Fatigue Testing Systems
8872
The 8872 fatigue testing system is ideal for fatigue and static testing of biomedical, advanced materials, and manufactured components. The servohydraulic actuator is conveniently located in the crosshead for easy table mounting. The T-slot base makes it easy to secure orthopaedic specimens, automotive components, and manufacturing assemblies. The adjustable crosshead, actuator-mounted load cell, and corrosion resistant T-slot base with unique drain channel are essential for testing biomedical specimens immersed in a saline bath.
-
product
Material Testing
*Abrasion Testing*Adhesion Testing*Brittleness Temp.*Bursting Strength*Coating Testing*Coefficient of Friction*Compression Testing*Compression Set*Dart Drop Testing*Density Determination*Fatigue Testing*Fiberboard Testing*Flammability Testing*Flexural Testing*Foam Testing*Hardness Testing*Heat Deflection*Hydrostatic Testing*Impact Testing*Life Cycle Testing*Melt Index Testing*Plastic Testing*Ply Separation*Resin Content*Rubber Testing*Shear Strength Testing*Stress Crack Testing*Tear Testing*Temperature Testing*Tensile/Elongation*UV Exposure*Water Absorption*Wood Testing
-
product
Measuring Systems For Beverage Can Manufacture
SPECIAL WORKBENCH
Optik Elektronik Gerätetechnik GmbH
To ensure the high measuring accuracy of RINGMASTER and PUNCHMASTER also under rough environmental conditions, a special workbench was developed. The workbench is equipped with vibration isolators, so that the equipment works also stable, if the toolroom is located close to the production line. Based on its ergonomics the special table ensures a fatigue free work.
-
product
Electric Servo Motor Type Tension and Compression Tester
It is a tensile / compression fatigue / durability / performance tester for various materials and automotive parts that have an ultra low inertia AC servomotor mounted on the actuator.
-
product
Textile Testing Equipment
Manufacture and supply a wide range of textile testing equipments. Our machines all meet with: ISO, ASTM, AATCC, BS, EN, DIN, JIS and other requireable standards. Yarn, Fiber and fabric testers. Strength, Abrasion, pilling, flammability fatigue, peeling, appearance, etc. testing.
-
product
ElectroForce Cardiovascular Test Instruments
From bare metal stents to heart valves to pacemaker components, we offer the most comprehensive portfolio of cardiovascular device testing solutions. For more than 20 years, medical device manufacturers have trusted ElectroForce as the world leader in accelerated fatigue test instruments.
-
product
Optical Fiber Cable Testing Equipment
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
product
Electric Vertical Test Stand
WDW-L series
Jinan Testing Equipment IE Corporation
Electric Vertical Test Stand is a tensile compressive test stand especially designed to match push-pull force gauge. This series pf electric vertical test stand has good stability, wide application range and is convenient to use. The electric vertical test stand has stepless speed-adjusting uniform motion, digital display of the testing speed and converting mode between manual and automatic operation. The vertical test stand is specialized for tension/compression test, insertion/withdraw test, fatigue test and fracture test.
-
product
Flexometer
EKT-2002GF
By means of applying constant load and compression frequency to the test specimen, this instrument could help the user to understand the history of Heat Built-up and dynamic fatigue poeperties of rubber compounds. For example, while tests the tire compound, it could provide the information of rolling resistance. Pt100 temperature sensor, temperature controller in PID parameters control, and air circulator are adopted to ensure the stable temperature control.
-
product
Strain and Fatigue Testing
ATA engineers have developed the skills and tools necessary to solve intricate and complex strength and fatigue problems.
-
product
Load & Fatigue Testing
DATASYST Engineering & Testing Services, Inc.
Due to variations in types and levels of load and fatigue exposure, DATASYST works with each client to determine the best possible test plan to capture the information and issues that may be present in application.
-
product
ElectroPuls
With more than ten years of running tests over billions of cycles, ElectroPuls systems are the established materials testing instruments using patented linear motor technology. Offering slow-speed static and high-frequency fatigue testing, this versatile testing capability means ElectroPuls systems are ideal for any lab or office space. Choose from axial only or combined axial-torsion systems that can deliver up to 10kN and 100Nm. Available in 3 sizes, simply pick the one that's right for you. ElectroPuls, a simpler, smarter, safer way to meet your testing needs.
