Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
PXI/cPCI Modular Embedded Controller - PXI 2.0/PCIe 3.0 Compatible, Max 512MB DRAM (256MB Installed)
TE9500-1200
TSI's modular approach to PXI embedded controllers provides maximum flexibility and upgradeability for most, if not all, PXI embedded controller requirements. The TE9500 series of embedded controllers is based on the industry standard ETX (embedded technology extended) SOM (system-on-module) form factor. Whether you choose a power saving Celeron CPU or a high performance mobile Pentium III, the TE9500ís integrated interfaces and upgradeable options apply across all models of the TE9500 series of controllers. The TE9500 series gives you the ability to control your controller.
-
product
ScanBridge
JT 2154
The JT 2154 is an experiment board based on National Semiconductor’s STA111 device, aimed at users looking to utilise addressable bridge/multiplexors within their designs, and thus set-up ‘system level’ JTAG access. The unit can also be used in semi-permanent installations to expand the TAP (Test Access Port) count on JTAG Technologies controllers in order to address highly segmented designs. Built-in support for ScanBridge-type devices within ProVision allows easy set-up of TAP assignments and device addressing.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
product
Imbedded A5 Processor Test Interface
Advanced Microtechnology, Inc.
Advanced Microtechnology has extended the application of its Optimum product line with theintegration of ARC5 imbedded test functions. Up to 40 controllers may be independently powered and monitored for functionality using the process test interface of the Optimum WinAOS application. Each part may have 2 separate biases featuring both current and voltage monitoring. Independent test is implemented through a standard JTAG interface. A separate serial clock and command interface may be used if required to provide device initialization sequences. JTAG control is muxed to each part through the use of an independent clock for each part. All of the ARC processor registers and memory space may be tested through the JTAG I/O.
-
product
High-Performance LAN & USB JTAG Controller
NetUSB II™
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires a controller with high performance specifications and diverse features.
-
product
Production Stand-Alone
PSA
Using PSA, test engineers can build sequences of applications in the built-in AEX (Application EXecutive) manager using if then else goto capabilities. Sequence builders can also include additional capabilities through DOS/Win command line calls, create serial number logged test reports, export tests results to a database etc.. PSA includes drivers for all JTAG Technologies controller hardware past or present.
-
product
JTAG Boundary-Scan Controllers
Corelis has developed a wide range of high-performance boundary-scan controllers that are compatible with buses such as USB 2.0, PCI, PCI Express, and Ethernet. Many of Corelis’ boundary-scan controllers operate up to 100 MHz sustained TCK frequency.
-
product
TAP Adapter for Corelis JTAG Controllers
Low Voltage Adapter
High technology, energy efficient, and small form factor products push JTAG interfaces to the limits; low power and high performance means low voltage, high speed, and high drive requirements. Building specialized interface circuits on product Printed Circuit Boards (PCBs) is inconvenient and costly—an out-of-the-box, external solution is needed.The Corelis Low Voltage adapter is an add-on accessory that provides existing scan controllers with an active, plug-in interface to access low voltage scan chains, without sacrificing performance.
-
product
JTAG Functional Test
JFT
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
-
product
Multiport JTAG Tester
XJQuad
XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).
-
product
Mixed Signal JTAG Tester
JT 5705
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
product
JTAG Live Controller
The JTAG Live Controller is USB connected and powered and features a single test access port in JTAG Technologies standard 10-way IDC pin-out. The JTAG Live controller is a smart, low-cost and easy-to-use USB JTAG/Boundary-scan interface.
-
product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
High-Speed USB 2.0 JTAG Controller
USB-1149.1/1E
The USB-1149.1/1E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/1E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
Remote Intelligent Pod
ScanTAP
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
product
JTAG Boundary-Scan Hardware
JTAG Boundary-Scan Hardware by Corelis, including boundary-scan controllers, 12C serial bus protocol analyzers & exercisers, JTAG boundary Scan Modules, high-volume production JTAG systems, 7 support for 3rd party JTAG controllers
-
product
Boundary-Scan Controller for PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37×7/PXIE
High speed and performance JTAG Boundary-scan controller for PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
product
JTAG 3rd Party Controller Support
Corelis offers support for a variety of devices and instruments from third-parties in an effort to provide existing test platforms comprehensive JTAG test execution with Corelis ScanExpress software products. Supported instruments include National Instruments PXI-655x HSDIO and Teradyne Di-Series modules. Corelis also provides support for JTAG testing with FTDI FT2232 ICs embedded on a unit under test (UUT).
-
product
Boundary-Scan Test / In-System Programming Controller
CPXI-1149.1/Turbo
The CPXI-1149.1/Turbo is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the CPXI-1149.1/Turbo offers up to 80 MHz clock rates on 4, 8, or 32 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
Controllers
onTAP’s THREE TAP CONNECT JTAG
Connect the TAP CONNECT JTAG Controller to your application with either the Xilinx ribbon cable, flying leads, or Altera style adaptors. The onTAP TAP CONNECT Controller automatically senses and adjusts to target I/O voltages and interfaces to devices operating at 1.8 to 5.0 VDC for the standard controller, or 0.99 to 3.6 VDC for the low voltage controller, using the VREF voltage from the target chain. If there is no VREF available, you can set the voltage for the target application from the TAP CONNECT Controller. This facilitates easy configuration to many different JTAG ports, which is helpful in design and manufacturing.
-
product
Embed functional-test
ScanWorks Embedded Diagnostics
The ScanWorks platform for embedded instruments is supported by a wide variety of hardware controllers and accessories with which engineers can connect ScanWorks to their unit under test (UUT). Hardware is available for development, production and repair environments. The test platform required for ScanWorks is either a standard PC or a system with a built-in (embedded) JTAG controller.
-
product
TAP Pods
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
Transient Suppression for Corelis JTAG Controllers
TAP Protection Adapter
Transient events such as Electrostatic Discharge (ESD), inductive switching, and lightning can damage electrical equipment, leading to costly repairs and test equipment down-time, reducing production capacity and increasing time-to-market.The Corelis TAP Protection Adapter is designed to enhance protection to any Corelis JTAG controller, shielding against harmful events using a combination of electrical defenses.The compact adapter features series resistors and transient voltage suppressor (TVS) diodes to mitigate damage to the JTAG controller. Protect your investment and enjoy peace-of-mind with the TAP Protection Adapter.
-
product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
product
USB JTAG controller
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
product
Boundary-Scan Controllers
Boundary-scan test and programming applications are only as dependable as the hardware they run on. JTAG Technologies has the industry’s most reliable IEEE 1149.x high speed and performance JTAG controllers, JTAG interfaces and more. To reliably execute your test and programming applications you can choose from a range of different controllers with different performance capabilities and form factors. For use in design, production and manufacturing and service.
-
product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
JTAG Probe
MAJIC
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
