Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Dual Transfer Switch 18GHz 50Ω SMA
40-782-522
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
product
PXIe-6674T, OCXO PXI Synchronization Module
781037-01
PXIe, OCXO PXI Synchronization Module—The PXIe‑6674T generates and routes clocks and triggers between devices in a PXI Express chassis as well as to other PXI and PXI Express chassis or third-party instrumentation. The PXIe‑6674T unlocks the advanced low-voltage differential signaling (LVDS) trigger signals PXIe‑DStarA, PXIe‑DStarB, and PXIe‑DStarC, on PXI Express while fully supporting the PXI trigger lines. The PXIe‑6674T can generate two types of clock signals: a highly stable 10 MHz clock based on an onboard precision oven-controlled crystal oscillator (OCXO) reference and a second clock from the direct digital synthesis (DDS) clock generation circuit.
-
product
High Performance Data Acquisition
CPCI-AD8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8/16 can also accept external scan and trigger signals from a front panel connector.
-
product
Weight Drop Controller
WDC
The WDC unit consists of the following: *Weight Drop Relay Control System *Radio Trigger Module (RTM) *Remote Control Box *Radio*Hammer Switch The WDC provides following features: *Automatic cycling with user entered number of hits*Time Delay Display (Time from fire command to hit)*GPS interface for position and timing*Remote Control Box
-
product
PXI/PXIe Trigger-Module
PXT(e)1741
Easy linkage of various external modules to the PXI(e) trigger busHigh configurable trigger matrix12 independent configurable trigger linesInputs/Outputs compatible with 5 V TTL standardSoftware controlled triggering of any target device
-
product
AXIe 5-Slot Chassis
M9505A
The M9505A AXIe Chassis is fully compatible with the AXIe 1.0 specification. It includes an embedded system module (ESM) that does not take up an instrument slot. This system module performs the chassis management functions contained in the AXIe specification. Additionally, it provides PCI and LAN interfaces for connection to an external computer, external clock and trigger connectors, and Keysight-exclusive, inter-chassis synchronization connectors. The local bus implemented in the M9505A provides the maximum 62 pairs allowed by the AXIe specification. Combine the M9505A with the M9048A PCIe Desktop Adaptor to achieve the highest system bandwidth.
-
product
cDAQ-9136, 1.91 GHz Quad-Core Atom, 4-Slot, CompactDAQ Controller
784239-01
1.91 GHz Quad-Core Atom, 4-Slot, CompactDAQ Controller - The cDAQ‑9136 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom quad-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9136 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9136 with up to four C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
cRIO-9054, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 4-Slot CompactRIO Controller
786425-01
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 4-Slot CompactRIO Controller - The cRIO-9054 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
TB-2632B , Screw Terminal, PXI Module Multiplexer Terminal Block
781689-01
The TB-2632B provides the necessary routing to configure the NI PXI-2530B PXI Multiplexer Switch Module as a 1-wire 8×16 matrix. You can directly connect the TB-2632B to the front panel I/O connectors of the PXI-2630B. The TB-2632B includes screw terminals to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
product
Pulsar 4 Channel Interface
Pulsar-4 7Z01201
Ophir’s 4 channel Pulsar interface turns your PC or laptop into a full fledged Ophir multi-channel laser power/energy meter. Just install the software, plug the laser measurement sensor into the Pulsar and the USB cable from the Pulsar to the PC USB port. With the Pulsar-4, you can connect up to 4 laser measurement sensors to each module, monitor each pulse at up to 25 kHz and utilize external trigger.
-
product
PXIe-1092, 10-Slot (7 Hybrid Slots, 1 PXI Express System Timing Slot, 1 Peripheral Expansion Slot), Up to 24 GB/s PXI Chassis
786991-01
PXIe, 10-Slot (7 Hybrid Slots, 1 PXI Express System Timing Slot, 1 Peripheral Expansion Slot), Up to 24 GB/s PXI Chassis - The PXIe-1092 features a high-bandwidth backplane and up to 82 W of power and cooling in every slot to meet a wide range of high-performance test and measurement application requirements. The all-hybrid backplane enables excellent flexibility for instrumentation module placement by accepting PXI Express modules in every slot and PXI hybrid-compatible modules in up to seven slots. It also offers a Timing and Synchronization option that includes a built-in oven-controlled crystal oscillator (OCXO) for increased clock accuracy and external clock and trigger routing. The chassis includes a peripheral expansion slot in Slot 10 to provide power only for multiple-slot wide modules.
-
product
4-Channel High Speed Position Comparison and Trigger Module
ECAT-TRG4
The ECAT-TRG4 is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
product
TB-2630B , Screw Terminal, Ribbon, PXI Module Multiplexer Terminal Block
781687-01
The TB-2630B provides the necessary routing to configure the PXI-2630B PXI Multiplexer Switch Module as a single, dual, or quad 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2630B to the front panel I/O connectors of the PXI-2630B. The NI TB-2630B features ribbon cable headers to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
product
Distributed 4-Axis Motion Control Modules (With High-Speed Trigger Function)
MNET-4XMO-(C)
The MNET-4XMO is a 4-axis motion controller module for Motionnet distributed motion systems. It can generate fast frequency pulses (9.9 MHz) to drive stepper or servomotors in the machine automation field. As a motion controller, it can provide comprehensive motion functions which include 2 axis circular interpolation, 2-4 axis linear interpolation, or continuous interpolation for continual velocity and so on. Also, changing position/speed on the fly is available with a single axis operation.
-
product
cDAQ-9133, 1.33 GHz Dual-Core Atom, 8-Slot, CompactDAQ Controller
783686-01
1.33 GHz Dual-Core Atom, 8-Slot, CompactDAQ Controller - The cDAQ‑9133 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 16 GB nonvolatile storage for data-logging and embedded monitoring. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9133 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input. You can combine the cDAQ‑9133 with up to eight C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
cDAQ-9135, 1.33 GHz Dual-Core Atom, 8-Slot, Extended Temperature CompactDAQ Controller
783688-01
The cDAQ‑9135 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring in extreme environments. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9135 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9135 with up to eight C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
AXIe 2-Slot Chassis
M9502A
The M9502A AXIe Chassis is fully compatible with the AXIe 1.0 specification. It includesan embedded system module (ESM)that does not take up an instrument slot. This system module performs the chassis management functions contained in the AXIe specification. Additionally, it provides PCI and LAN interfaces for connection to an external computer, external clock and trigger connectors, and Keysight-exclusive, inter-chassis synchronization connectors. The local bus implemented in the M9502A provides the maximum 62 pairs allowed by the AXIe specification. Combine the M9502A with the M9048A PCIe Desktop Adaptor to achieve the highest system bandwidth.
-
product
640 Gb/s Digital Signal Processor
M8132A
The M8132A is a powerful digital signal processing module featuring two customers accessible Xilinx Ultrascale+ FPGAs, four optical data interfaces (ODI) running at up to 160 Gb/s in+out each, and a PCIe Gen3 x8 link to the AXIe backplane. In addition, the module provides a trigger input and output, synchronization input and outputs for deterministic latency between compatible digitizers and AWG modules as well as a 10-general purpose I/O pins. The M8132A is part of Keysight’s Wideband Solution Platform that consists of a portfolio of compatible instruments, including digitizer, arbitrary waveform generator, digital signal processor and storage modules.
-
product
PXI-2527, 32‐Channel, 300 V, 2‐Wire PXI Multiplexer Switch Module
778572-27
32‐Channel, 300 V, 2‐Wire PXI Multiplexer Switch Module—The PXI‑2527 is a high‐voltage PXI multiplexer switch module that is ideal for medium‐ to high‐density automated test applications. Featuring high-power electromechanical relays, the PXI‑2527 is the perfect front end for the PXI DMM modules, offering simple channel expansion for a variety of measurements. The PXI‑2527 supports multiple channel configurations including 64x1 1‑wire, 32x1 2‑wire, and 16x1 4‑wire. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
cDAQ-9179, 14‑Slot, USB 3.0 CompactDAQ Chassis
783597-01
14‑Slot, USB 3.0 CompactDAQ Chassis - The cDAQ‑9179 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements with the higher performance data streaming of USB 3.0. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9179 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
product
cDAQ-9137, 1.91 GHz Quad-Core Atom, 8-Slot, CompactDAQ Controller
784240-01
1.91 GHz Quad-Core Atom, 8-Slot, CompactDAQ Controller - The cDAQ‑9137 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom quad-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9137 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9137 with up to eight C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
LXI Series
LXI instruments range from LXI modules that plug into a chassis to standalone instruments that have dedicated LXI and hardware trigger bus connections. These instruments can be configured to measure many types of variables to precise values. Some of these instruments also incorporate 6.5-digit DMMs as well as user-programmable digital alarm circuits.
-
product
In-Circuit Testing and Test Engineering
GenRad 2287
3560 Hybrid Test NodesWindows InterfaceTotal GenRad 227X Migration Capability20 Mhz Clock, Sync, and Trigger, 5 Mhz data ratesVector Test for VLSI, PLCC’s & ASICSTest Express Vectorless TestingMultiple Chain Boundary ScanAnalog Functional Test Module
-
product
IC-3120, 1.91 GHz Intel Atom Quad-Core Processor, 2-GigE Port Industrial Controller
784959-01
The IC‑3120 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3120 offers two Gigabit Ethernet ports with Power over Ethernet (PoE) technology, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
product
PXIe Full Hybrid Chassis, 21-Slot (Gen 2)
42-927-101
This 21-slot PXIe Chassis provides one PXIe system slot and 20 hybrid-compatible slots for application flexibility. The chassis utilizes three PCI segments with a dedicated PCIe-to-PCI bridge module for the hybrid slots. The PXI-specific high-accuracy clocks and trigger signals are generated and controlled by an independent clock module attached to the rear of the backplane.
-
product
4-Channel Motion Control and High-Speed Trigger and Module for the Bridge Connected to EtherCAT
ECAT-4XMO
The ECAT-4XMO is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like leaner, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
product
PXI Switch - 4x8 2-Wire Matrix Module
PXI-7931
ADLINK PXI-7931 is a matrix module with 32 cross-point 2-wire relays (DPDT, 2 Form C). The default configuration of the PXI-7931 itself is a 4-group 2x4 2-wire matrix. With the termination board, TB-6231, users could flexibly choose one of the configurations: one 4x8, two 4x4, one 2x16, two 2x8 and four 2x4. Any contact of the PXI-7931 can connect to other contacts, individually or in combination. The PXI-7931 matrix module simplifies the wiring and makes it easy to change the internal connection path. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7931, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
PXI Bit-Pattern-Receiver Family
PXI(e)530x
Up to 6.6 MS/s with 7 Bit pattern widthUp to 2 independent modules with 4 simultaneously working channelsBased on VX Instruments FlexCPP for easy custom designHighly configurable trigger engineMultiple instrument and channel synchronization possibilitiesIndependent sample clock input for every channel
-
product
Data Acquisition DSP based 16 channel
The CPCI-AD8/16 module provides a 3U high performancedata acquisition subsystem. There are (8) eight or (16)sixteen 100/200 KSPS ADC’s for maximum performance.The Local DSP can be used to simply move data samplesto the CPCI bus or can provide processing functions suchas limit checking, FFT’s, digital filtering, etc. Software canbe downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protectionand gain on a per channel basis. The CPCI-AD8/16 canalso accept external scan and trigger signals from a frontpanel connector
