Filter Results By:
Products
Applications
Manufacturers
-
product
Subsea Data Logger
DL-3.0
The Subsea Data logger is proprietary data logger design by DLM for use in the offshore industry. Comprising of multiple on-board sensors and with extra capacity for external mV or mA inputs, the DL-3.0 can sample on-board and external sensors at customisablesample rates of up to 800Hz.
-
product
Fluid Power Actuators
Subsea
We are well versed with supplying subsea product to meet the harsh conditions and stringent demands of subsea applications. The subsea product range encompasses actuator and gearbox designs for retrievable and non-retrievable applications. Our engineering group works closely with contractor and end-user engineers to meet specific project requirements.
-
product
Subsea Oil-In-Water Analyzer
The Mirmorax Oil-in-Water analyzer is based on an ultrasonic measurement technique in which individual acoustic echoes are characterized using advanced signal processing.
-
product
Multibeam Echosounder - Subsea
SeaBat T50-S
The T50-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with a Subsea Sonar (SSP), the T50-S produces unprecedented clean data, providing faster operational surveys and reduced processing time in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel.
-
product
Load Pin Products
DLM are world renowned for the design and manufacture of custom design load pins for a host of industries, including offshore moorings, renewable energy and marine & subsea applications.
-
product
Subsea Imagery
With only 24% of the ocean floor being mapped with a submetric resolution, the ocean’s seabed is Earth’s last frontier. Mapping the seafloor, protecting marine habitats, hunting for wrecks, studying underwater geo-hazards…Those are challenges for the years to come.It is to help in that field, that Exail has developed a large range of sensors designed to address the full spectrum of subsea imagery applications, from sub-bottom profiling and seabed mapping to water column monitoring.
-
product
Sensor String System Flexible Subsea Observatories
SeaGuard Sensor String
The Aanderaa SEAGUARD® Sensor String Systems are complete and flexible subsea observatories for measurements of e.g. dissolved oxygen, conductivity, temperature, current, pressure and tide.
-
product
Acoustic Load Shackle
ALS-2.0
The Acoustic Load Shackle is designed for subsea operations where load monitoring is required, either for short term operations lowering an item to the seabed or for longer periods monitoring dynamic loads.
-
product
Cormon Integrated Monitoring Software
CIMS
Cormon Integrated Monitoring Software (CIMS) processes real-time corrosion, erosion, pressure, or temperature data from up to 50 monitoring sensors to provide a complete picture of pipeline and device health. Alarm functions can be configured to ensure that potential issues are identified with ample time for correction, reducing operational risk and unplanned downtime. CIMS is the only industry software that can bring together data from both topside and subsea sensors, giving operators a comprehensive view into the entire asset integrity program.
-
product
Subsea Data Logging Tensile Link
SUBD-3.0
The Subsea Data logging Tensile Link is a robust Tensile Link used for measuring loads on subsea mooring lines, underwater deployments and other similar applications. The instrument measures and records the applied load using an internal data logger which was developed by DLM Design Engineers.
-
product
Subsea Tensile Link
SUBT-3.0
The Subsea Tensile Link is specially designed for working in subsea conditions and is used for measuring tensile loads. With an optional integral 4-20mA amplifier the load cell is packaged in a wooden case with a subsea rated signal cable to customer specific lengths or alternatively can be supplied with a TW-3.0-S display. Fully sealed with a subsea connector and pressure tested to over 250Bar the load cell is the ideal instrument for easily and accurately measuring subsea loads.
-
product
Extended Ethernet Flying Lead (E²FL)
Due to vast geographies and complex field layout configurations, Subsea Ethernet transmission requirements may reach beyond the 100 meter maximum. Extended Ethernet Flying Leads (E²FL) enables Ethernet transmission beyond the limits of the previous 100 meter Ethernet assemblies.
-
product
Multibeam Echosounder - Subsea
SeaBat T20-S
The T20-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with the all-new Subsea Sonar Processor the T20-S provides the highest quality survey data in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel. Smaller form factor and reduced operational power to extend mission time for battery powered underwater vehicles. Internal data storage for self-contained survey solution, and interfacing via standard Ethernet to reduce integration time.
-
product
Subsea Multiphase Sampler
The Mirmorax Subsea Multiphase Sampling System provides the operator with a sample that, independent of flow regime and compositional mix, is a true volumetric representation of the flow.
-
product
10 kV Subsea Power System
The Teledyne Oil and Gas 10 kV subsea power electrical connection system is a three-phase system rated to 250 A and 6/10 (12) kV. The electrical connection system is designed to provide power to motors used for subsea pumping systems.
-
product
Load Pins
They are used in many diverse applications including cranes, winches, agricultural equipment (such as tractors), fishing, marine, offshore, subsea, aerospace, process industries, mining, hoisting gear, elevators and floor conveyors, cable laying machinery and many others. The load information provided by the pin can be used for process control, weight/force measurement, overload protection and safety related aspects.
-
product
Bonnet EFS for Horizontal Wellhead Completions
This Electrical Feedthrough System design provides a high-reliability circuit for transmitting electrical signals from downhole gauges through the wellhead and Subsea Tree to the Subsea Control Module (SCM) for topside monitoring. The system incorporates Teledyne DGO's high integrity glass-seal technology in three critical pressure barriers for maximum long-term reliability. The feedthrough system creates a permanent connection to the Subsea Control Module when the tree is installed onto the wellhead. In addition, a permanent rig-based DHG cable termination is completed to connect the control line to the feedthrough system. The DHG connector is available with a variety of sealing packages, including fully testable, dual metal-to-metal sealing of all downhole tubing hanger interfaces.
-
product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
product
Electrical Penetrator with High Pressure Barrier, Rated at 10 kV and 250 A
P10-250 Electrical Penetrator
For higher subsea power requirements, the P10-250 from Teledyne ODI is designed to provide reliable barrier protection at extreme pressures and temperatures. The penetrator extends through a wall or bulkhead and connects to medium voltage cables to supply an external power source. In electric submersible pumping (ESP) applications, the penetrator transfers power to the motor while maintaining a pressure barrier between the motor and the seawater.
-
product
Subsea Pipe and Cable Detection & Tracking System
HydroPACT Dualtrack
Dualtrack is the combination of the 440 and the 350 systems to provide the ultimate subsea detection system, capable of tracking and surveying pipes and cables via ROV deployment.It utilizes the same industry standard pulse induction technology as the 440 system to survey accurately regardless of vehicle heading. The accompanying display and control software is Windowsâ„¢ based providing a familiarity factor that a specifically built interface would not.
-
product
Next Generation Subsea Attitude and Heading Reference Systems
TOGS
The new TOGS subsea navigation system is built on core TSS fibre optic gyro (FOG) navigation technology with significant improvements in efficiency and functionality. It is available in three standard heading accuracy variants: 0.1° (TOGS1), 0.3° (TOGS3) and 0.5° (TOGS5), all rated for operational depths to 4,000m or 6,000m. Attitude data is delivered via accurate roll/pitch measurement capabilities of 0.01° (TOGS1) and 0.05° (TOGS3 and TOGS5), and a heave performance of 5cm or 5%.
-
product
Specialised Load Monitoring Products
DLM have a wide range of specialist monitoring equipment for industry specific applications, ranging from saddleback monitors for PLGR operations to logging subsea loads with our data loggers.
-
product
Single Pin Horizontal EFS
Teledyne DGO offers an advanced, high-reliability subsea wellhead single channel electrical feedthrough system for use in intelligent completions with permanent downhole instrumentation. The connection system is designed for long-term reliability in the demanding subsea and downhole environments with sour well (H2S) conditions, as well as aggressive production and packer fluids.
-
product
Subsea Shackle Load Cell
SUBS-3.0
The Subsea Shackle Load Cell has been designed to measure loads in a subsea environment. DLM’s subsea shackles are suited to fit leading industry Crosby and GN shackles.
-
product
15kV Subsea Power System
The Teledyne Oil and Gas 15kV subsea power electrical connection system is a three-phase system rated to 220 A and 8.7/15 (17.5) kV. The electrical connection system is designed to provide power to subsea production systems.
-
product
LED Floodlight up to 6000m, 120Vac 10,000 Lumen
U Light
The Teledyne Bowtech U light is for use on subsea platforms that operate down to 6000m depths, requiring a 120Vac Ultra- bright 10,000 lumen, LED Floodlight. The 80° wide LED floodlight beam angle is ideal for colour video inspection tasks. Housed in hard anodised aluminium, this deepwater LED floodlight measures in at 82mm Ø by 148.4mm long and comes with thermal protection ensuring that the light does not overheat if accidentally run in air. The U Light has the capability of being controlled externally by normal ON / OFF power switching or by using phase control diming techniques enabling the operator to produce a varying level of light intensity. This extremely robust U Light LED floodlight is ideal for clear visibility in deep depths on larger work class ROVs, Trenchers and Tractors.
-
product
Omnisens Securing Power Cable Integrity
https://www.omnisens.com/uploads/1/2/0/5/120592129/published/omnisens-cobra-logo-white-2014-06-10.png?1546958203
In both underground and subsea cables incipient faults often result in temperature events. Using optical fibers integrated into the power cable or laid close by, Distributed Temperature Sensing (DTS) helps detect changes and faults allowing the operator to intervene before the cable fails. It is suitable for deployment in any cable where an optical fiber is present, including HVDC, HVAC, export, inter-array, transmission and distribution.
-
product
Wet-Mateable Connector, 10k V, 250 A
Nautilus WM10-250
Trends in subsea oil & gas production are moving towards deeper water and longer step out distances. These trends drive demand for higher power equipment and higher power delivery and distribution capabilities subsea with high pressures and temperatures. Teledyne ODI'™s Nautilus WM10-250 is designed with the benefit of advanced material science testing and certification, and with insulation and redundant sealing systems for reliable performance in long-term harsh environments.
-
product
SEA CLIP™ Sensor & Aqua MER™ Meter
The SEA CLIP™ by Swain Meter is a high-quality, hydraulically actuated clamp-on DC ammeter for ROV. It is useful for measuring DC currents in subsea cables, cathodic protection systems, and subsea pipes up to 4” in diameter. The SEA CLIP™ can be used with an optional 200-foot cable to a topside meter, or in concert with the Aqua MER™ subsea meter at depths up to 6900 feet of seawater.The Aqua MER™ ROV meter is based on Swain’s proven MER2™ technology, specially adapted to the demanding requirements of the subsea environment and updated to provide RS-485 communication over twisted pair, or fiber optic data transmission protocols.
-
product
Modular Connectorized Distribution Unit
MCDU
The Modular Connectorized Distribution Unit (MCDU) is a modular family of factory-qualified subsea distribution units that provide oil-filled, pressure-balanced junctions for flexible underwater configurations.A new configuration has recently been introduced with a lighter, more cost-effective frame, highly visible ROV lifting handles, and wide openings to facilitate installation and removal of the housing. The compact frame design negates the need for lifting wires, making it easy for ROVs to install and retrieve the unit from the sea floor.
